Precor TRM 800 warranty Adjusting the Running Belt, To adjust the running belt

Page 50

48	Assembling and Maintaining TRM 800-Series Treadmills

5.Check the belt tension of the step-up and drive belts.

6.Clean and lubricate the lift motor screw with an approved grease such as SuperLube® with Teflon® or Mobil 1® synthetic grease (adjustable-ramp models only).

7.Check all fasteners for proper tightness and torque.

8.Replace all covers.

9.Verify that the unit sits squarely on the floor. All of its feet should be touching the floor and the unit should not rock or wobble when in use. If not, re-level it as described in Leveling the Unit.

Adjusting the Running Belt

If you are unsure about adjusting the running belt, call Precor Customer Support (refer to Obtaining Service).

CAUTION: For your safety, use the power switch to turn OFF the treadmill before making any adjustments. Do not adjust the running belt when someone is standing on it.

Important: This procedure uses the terms "left" and "right" as they would appear to a person standing behind the treadmill and facing the console. Make all belt adjustments on the adjusting bolts at the rear corners of the treadmill, using the hex key provided, and do not turn either bolt more than ¼ turn before checking the alignment of the running belt again. Overtightening the adjusting bolts can damage the treadmill.

To adjust the running belt:

1.Locate the adjusting bolts in the end caps at the rear corners of the treadmill, as shown in the following diagram.

Figure 29: Location of the adjustment bolt

2.Using the hex key, move one of the adjusting bolts ¼ turn counterclockwise to loosen it.

Image 50

Contents Assembling and Maintaining TRM 800-Series Treadmills Page Page Trademark Note Intellectual Property NoticeImportant Safety Instructions Safety PrecautionsAssembling and Maintaining TRM 800-Series Treadmills Safety Code Educating Users Hazardous Materials and Proper DisposalProduct Recycling and Disposal Regulatory Notices for the Rfid ModuleIndustry Canada Radio Frequency Interference RFIFederal Communications Commission, Part European Applications Safety Approvals for Cardiovascular EquipmentRegulatory Notices for Cardiovascular Exercise Equipment Cardiovascular Type EquipmentUser’s authority to operate the equipment Treadmill Grounding Instructions Electrical Recommendations 240 V TreadmillsObtaining Service Obtaining Updated Documentation North American 120-volt, 20-amp power receptacleTable of Contents Commercial Cardiovascular Equipment Limited Warranty To prepare the treadmill for assembly Assembling the TreadmillInstallation Requirements Required ToolsHardware Kit not to scale FastenersUnpacking the Cables To unpack the cablesRemoval and replacement of the rear fairing cover To begin assembly of the frame Assembling the FrameUpright support attachment, right side To thread cables through the frame PointUpright support attachment, left side Handrail and console assembly attachment To secure the fasteners Completing AssemblyTo complete assembly of the treadmill base Attaching the Power Cord Clips To attach the power cord clipsChecking Treadmill Alignment and Adjusting the Running Belt Power cord placement under front of treadmillLeveling the Unit To level the treadmillPlugging In the Power Cord Breaking in the EquipmentAssembling and Maintaining TRM 800-Series Treadmills Installing the Console Threading the Cable Assembly P80To thread the cable assembly Removing the access cover from the P80 consoleConnecting Cables P80 Connecting the Television Cable To connect the television cableConnecting the Ethernet and Base Unit Data Cables Connecting the television cableConnecting the Heart Rate Sensor Cable Connecting the Power CableCompleting the Console Installation P80 To complete the installationThreading the Cable Assembly P30 and P20 Connecting Cables P30 Connecting Cables P20 Completing the Console Installation P30 and P20 Reassembling the Treadmill Fairing To reassemble the fairingVerifying That the Heart Rate Display Is Operational To verify that the heart rate display is operationalAssembling and Maintaining TRM 800-Series Treadmills Maintenance Daily CleaningDaily Inspection Weekly Maintenance Monthly MaintenanceAdjusting the Running Belt To adjust the running beltChecking the Alignment of the Running Belt To align the running beltTo put the treadmill into an inclined position for moving Storing the Chest StrapMoving the Equipment Long-Term Storage Assembling and Maintaining TRM 800-Series Treadmills Entering the Safety Code To enter the safety code and start the treadmillUsing the Treadmill Safety Clip Restart switchLocation Weight LimitTurning the Treadmill On and Off Assembling and Maintaining TRM 800-Series Treadmills Limited Warranty Warranty Periods and CoverageConditions and Restrictions Exclusive Remedies Exclusion of Consequential and Incidental Damages Complete this portion and keep for your recordsPage Precor Incorporated