Precor TRM 800 warranty Checking the Alignment of the Running Belt, To align the running belt

Page 51

Maintenance	49
If the belt tracks off center ... Then loosen ...
To the left	The right adjusting bolt
To the right	The left adjusting bolt

3.Recheck the belt position as described under Checking the Alignment of the Running Belt.

Note: If slippage occurs, tighten both adjusting bolts evenly until it stops. Do not overtighten the belt.

Checking the Alignment of the Running Belt

Proper alignment allows the belt to remain centered and ensures smooth operation. Realigning the belt takes a few simple adjustments. If you are unsure about this procedure, call Precor Customer Support (refer to Obtaining Service).

CAUTION: Take special care when aligning the running belt. Turn OFF the treadmill while adjusting or working near the rear roller. Do NOT wear loose clothing or allow your hair to hang loose during this procedure. Be very careful to keep your fingers and any other object clear of the belt and rollers, especially in front of the roller and behind the deck. The treadmill will not stop immediately if an object becomes caught in the belt or rollers.

To align the running belt:

1.Make sure that the running surface is as level as possible. If necessary, adjust the rear feet as shown in the Assembly Guide to level the treadmill.

Note: Adjusting the rear feet cannot compensate for extremely uneven surfaces. If you cannot make the running surface level and stable, move the treadmill.

2.Turn the treadmill ON.

3.Standing beside the treadmill (not on it), press GO on the console.

4.If necessary, enter the safety code by pressing the number keys in sequence. The running belt starts automatically after a 3-second countdown appears on the console.

5.Press the SPEED UP key until the console shows a speed of 3 mph (5 kph).

CAUTION: If you hear any chafing or the running belt appears to be getting damaged, stop the running belt immediately by pressing the red STOP button. Contact Precor Customer Support.

Image 51

Contents Assembling and Maintaining TRM 800-Series Treadmills Page Page Intellectual Property Notice Trademark NoteSafety Precautions Important Safety InstructionsAssembling and Maintaining TRM 800-Series Treadmills Safety Code Hazardous Materials and Proper Disposal Educating UsersRegulatory Notices for the Rfid Module Product Recycling and DisposalRadio Frequency Interference RFI Federal Communications Commission, PartIndustry Canada Cardiovascular Type Equipment Safety Approvals for Cardiovascular EquipmentRegulatory Notices for Cardiovascular Exercise Equipment European ApplicationsUser’s authority to operate the equipment Electrical Recommendations 240 V Treadmills Treadmill Grounding InstructionsNorth American 120-volt, 20-amp power receptacle Obtaining Service Obtaining Updated DocumentationTable of Contents Commercial Cardiovascular Equipment Limited Warranty Assembling the Treadmill To prepare the treadmill for assemblyRequired Tools Installation RequirementsFasteners Hardware Kit not to scaleTo unpack the cables Unpacking the CablesRemoval and replacement of the rear fairing cover Assembling the Frame To begin assembly of the frameUpright support attachment, right side Point To thread cables through the frameUpright support attachment, left side Handrail and console assembly attachment Completing Assembly To complete assembly of the treadmill baseTo secure the fasteners To attach the power cord clips Attaching the Power Cord ClipsPower cord placement under front of treadmill Checking Treadmill Alignment and Adjusting the Running BeltTo level the treadmill Leveling the UnitBreaking in the Equipment Plugging In the Power CordAssembling and Maintaining TRM 800-Series Treadmills Threading the Cable Assembly P80 Installing the ConsoleRemoving the access cover from the P80 console To thread the cable assemblyConnecting Cables P80 To connect the television cable Connecting the Television CableConnecting the television cable Connecting the Ethernet and Base Unit Data CablesConnecting the Power Cable Connecting the Heart Rate Sensor CableTo complete the installation Completing the Console Installation P80Threading the Cable Assembly P30 and P20 Connecting Cables P30 Connecting Cables P20 Completing the Console Installation P30 and P20 To reassemble the fairing Reassembling the Treadmill FairingTo verify that the heart rate display is operational Verifying That the Heart Rate Display Is OperationalAssembling and Maintaining TRM 800-Series Treadmills Daily Cleaning MaintenanceDaily Inspection Monthly Maintenance Weekly MaintenanceTo adjust the running belt Adjusting the Running BeltTo align the running belt Checking the Alignment of the Running BeltStoring the Chest Strap Moving the EquipmentTo put the treadmill into an inclined position for moving Long-Term Storage Assembling and Maintaining TRM 800-Series Treadmills To enter the safety code and start the treadmill Entering the Safety CodeRestart switch Using the Treadmill Safety ClipWeight Limit Turning the Treadmill On and OffLocation Assembling and Maintaining TRM 800-Series Treadmills Warranty Periods and Coverage Limited WarrantyConditions and Restrictions Exclusive Remedies Complete this portion and keep for your records Exclusion of Consequential and Incidental DamagesPage Precor Incorporated