Precor EFX534 owner manual Using Csafe Standard Equipment, User ID Entry Program Keys, Enter Reset

Page 26

C O M M E R C I A L P R O D U C T S D I V I S I O N

Press Enter once again and the Error Log appears. The EFX stores the last ten errors that have been detected. Press any ▼ or ▲ key to view the error codes.

Note: If the EFX has no errors stored in memory, a “– – –” appears on the display.

To view the odometer reading at the time the error was detected and the hours of use at the time the error occurred, press the Select key while the error code is being displayed.The Select key acts as a toggle between the associated information.

To clear (delete) the error log, press QuickStart for at least four seconds while viewing the list. Prompts appear on the display and confirm (OK) that the error messages have been deleted (“cleared”) from memory.

Important:You cannot retrieve the error log once you have deleted it.

USING CSAFE STANDARD EQUIPMENT

The EFX is fully compatible with CSAFE protocols. Once the unit is connected to a CSAFE master device and the user maintains a stride rate above 40 strides per minute, he or she is prompted to enter an identification number (user ID).

Note: If the optional battery recharger is plugged into the EFX and connected to an appropriate power source, then no pedaling is necessary for user ID entry.

Five zeros appear on the display. The left zero indicates that it is awaiting input. The following table provides information about the keypad functions:

User ID Entry:

Program Keys

 

 

▼or ▲

Enter

Reset

moves the blinking LED from field to field.

submits the displayed user ID. Note that if the five zeros are being displayed when the user presses Enter, the user ID entry is bypassed and the Course prompt appears.

resets the display to the Precor banner.

A message indicates when the user ID is accepted by the CSAFE master device. Then, the course prompt is displayed. See Quick Steps to Working Out on page 37.

Note: If the user’s stride rate drops below 40 strides per minute while using the CSAFE device connection, a prompt PEDAL FASTER appears. If the stride rate remains below the 40 strides per minute threshold for the next twenty seconds, the CSAFE connection is terminated. The word RESETTING appears on the display while the EFX disconnects from the CSAFE device.

To review information about CSAFE specifications, visit the web site at:

www.fitlinxx.com/csafe

Note: The EFX supports the CSAFE master device per the specifications found at the web site. However, exceptions do exist. If you have questions or need technical support, refer to Obtaining Service on page 7.

page 26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents M M E R C I a L P R O D U C T S D I V I S I O N Important Safety Instructions Safety Approval Hazardous Materials and Proper DisposalTable of Contents Back cover User’s authority to operate the equipment RFI Radio Frequency InterferenceEuropean Applications European ApplicationsEFX SELF-POWERED Features Obtaining ServiceAbout this Manual Equipment and prevent injuries to yourselfOther Equipment Unpacking the EFXStandard Equipment Acquiring the Appropriate ToolsHardware KIT Assembly Instructions Setting Up the EFXInstallation Requirements Diagram 5 Front base assembly M M E R C I a L O D U C T S V I S I O N Upright Diagram 9 Place the base on supportive blocks Bolts G and washers H Frame stabilizer Upright Tighten all mounting screws using a 9/16 wrench. Diagram Diagram 12 TightenDiagram 13 Secure Diagram 15 Secure Diagram 16 Level the unit Diagram 18 Insert the front end cap Removing the Locking PINSupplying Power to the EFX534 Testing the Heart Rate DisplayCustom Settings Mode Changing the Custom SettingsDetermining the Units of Measure Electrical power must be suppliedDisplay key functions within the Custom Settings Mode Reset, Enter, QuickStart Setting a Workout Time LimitSetting a Pause Time Limit User ID Entry Program Keys Using Csafe Standard EquipmentEnter Reset Center Display Features on the Display ConsoleEFX534 Display Select User Setup PromptsSetup Prompts Description QuickStartPress Quickstart at Following occurs Using Quickstarttm During the Setup PromptsWeight prompt Precor bannerCenter Display Informational Displays Prior to Shutdown Low BatterySmartrate Display Keys on the Display Console DefaultValues Prompts DefaultValueWeight Loss Zone Heart Rate FeatureUtilizing the Smartrate Feature Exercising on the EFXWorkout Tips Changing the Display Features Using the Select KEY Using the HandlebarsUsing the Stationary Handrail Quick Steps to Working OUT A course This is what happens PAUSE, Cool Down and Exit FeaturesCooling Down After a Workout Inserting the Locking PIN Press Reset Displays the Workout Summary bannerCool down Mode Pause Mode, youHill Climb Course Manual Mode and the Quickstarttm KEYCourses Interval CourseYour AGE To use the interval course, take the following stepsWeight Loss Course Cross Training CourseInspection MaintenanceCleaning the Equipment Storing the Polar Chest Strap Symptoms of a LOW BatteryUsing the Battery Recharger Servicing the EFX and Long Term StorageReplacing the Battery Battery Recharger Power CordExploded Views Exploded Views Exploded Views Exploded Views Exploded Views Exploded Views Exploded Views Thank You and Welcome to Precor Please indicate the type and number of products purchased Date of PurchaseProduct Serial Numbers How many members do you have?Conditions and Restrictions Limited WarrantyWarranty Periods and Coverage Complete this portion and keep for your recordsProduct Specifications Electronic Specifications
Top Page Image Contents