ProForm PFTL97007.0 user manual Make sure that the power cord is unplugged

Page 7

1.Make sure that the power cord is unplugged.

With the help of a second person, carefully tip the treadmill onto its left side. Partially fold the Frame (56) so that the treadmill is more stable; do not fully fold the Frame yet.

Remove and discard the two indicated bolts (A) and the shipping bracket (B).

Cut the ties securing the Upright Wire (38) to the Base (83). Locate the tie in the indicated hole in the Base, and use the tie to pull the Upright Wire out of the hole.

Attach a Base Pad (81) to the Base (83) in the location shown with a Base Pad Spacer (13) and a #8 x 1" Tek Screw (2). Then, attach another Base Pad (81) with only a #8 x 1" Tek Screw (2).

2.Remove the 3/8" Nut (8), the 3/8" x 2" Shoulder Bolt (43), and the shipping bracket (C) from the Base (83). Attach a Wheel (84) with the Bolt and the Nut that you just removed. Do not over- tighten the Nut; the Wheel must turn freely. Discard the shipping bracket.

3.Identify the Right Upright (78) and the Right Upright Spacer (79), which are marked with stickers. Insert the Upright Wire (38) through the Right Upright Spacer as shown.

See the inset drawing. Tie the long tie in the Right Upright (78) securely around the end of the Upright Wire (38). With the help of a second person, hold the Right Upright near the Base (83). Then, pull the other end of the long tie until the Upright Wire is routed completely through the Right Upright.

1

B

 

 

A

 

 

 

 

38

 

Hole

 

56

 

81

 

 

 

 

2

 

 

Tie

13

 

83

 

 

81

2

 

 

 

2

 

83

 

 

43

 

 

 

84

 

C

 

 

8

 

 

3

 

 

 

78

 

38

 

 

 

 

38

79

Long Tie

83

78

38Long

Tie

7

Image 7
Contents On the WEB QUESTIONS?Please do not Contact Call TOLL-FREETable of Contents Important Precautions Page Before YOU Begin Assembly Make sure that the power cord is unplugged Tighten the Nut the Wheel must turn freely Be careful not to pinch the Upright WireGers do not fully tighten the Bolts yet Do not fully fold the Frame yetNot Connected PROPERLY, the CON Sole MAY be Damaged When Power is Turned onBolts See steps 4 and 6. Tighten the 3/8 x 4 1/2Small Screws HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console Console DiagramInsert the key into the console HOW to Turn on the PowerHOW to Personalize Console Settings Select the user modeHOW to Identify Yourself AS User 1 or User Select a default user settingSet the date and time Start the walking belt and adjust the speed HOW to USE the Manual ModePersonalize console settings if desired Select the manual modeMeasure your heart rate if desired Select a preset classic workout HOW to USE a Classic WorkoutPress the Start button to start the workout Select an event training workout HOW to USE AN Event Training WorkoutSelect one of the four custom workouts HOW to Create a Custom WorkoutHOW to USE a Custom Workout HOW to View the Fitness Journal Information Mode HOW to Reset the Fitness JournalSelect the user mode. See on Reset the fitness journal Exit the user modeHOW to Adjust the Cushioning System HOW to USE the Stereo Sound SystemOptional Chest Pulse Sensor HOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Move the TreadmillProblem The power turns off during use TroubleshootingProblem The walking belt slows when walked on Page Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesKey No. Qty Description R0108AQty Exploded Drawing A-Model No. PFTL97007.0 R0108A Exploded Drawing B-Model No. PFTL97007.0 R0108A Exploded Drawing C-Model No. PFTL97007.0 Exploded Drawing D-Model No. PFTL97007.0 R0108A Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT