ProForm PFTL97007.0 user manual HOW to Turn on the Power, HOW to Personalize Console Settings

Page 14

HOW TO TURN ON THE POWER

IMPORTANT: If the treadmill has been exposed to cold temperatures, allow it to warm to room tem- perature before turning on the power. If you do not do this, the console displays or other electrical components may become damaged.

Plug in the power cord

 

 

 

 

 

 

 

 

 

 

 

 

(see page 12). Next, lo-

 

 

 

 

 

 

 

 

 

 

 

 

 

cate the reset/off circuit

 

Reset

 

 

 

 

 

breaker on the treadmill

 

Position

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

frame near the power

 

 

 

 

 

 

cord. Switch the circuit

 

 

 

 

 

 

 

 

 

 

 

 

breaker to the reset posi-

 

 

 

 

 

 

tion.

 

 

 

 

 

 

IMPORTANT: The console features a display demo mode, designed to be used if the treadmill is dis- played in a store. If the display lights as soon as you plug in the power cord and switch the reset/off circuit breaker to the reset position, the demo mode is turned on. To turn off the demo mode, hold down the Stop button for a few seconds. If the display remains lit, see THE INFORMATION MODE on page 23 to turn off the demo mode.

Next, stand on the foot rails of the treadmill. Find the clip attached to the key (see the drawing on page 13) and slide the clip onto the waistband of your clothes.

Then, insert the key into the console. After a moment, the display will light. IMPORTANT: In an emergency situation, the key can be pulled from the console, causing the walking belt to slow to a stop. Test the clip by carefully taking a few steps backward; if the key is not pulled from the console, adjust the posi- tion of the clip.

Note: If there is a sheet of clear plastic on the face of the console, remove the plastic. To prevent dam- age to the walking platform, wear clean athletic shoes while using the treadmill. The first time you use the treadmill, observe the alignment of the walking belt, and center the walking belt if neces- sary (see page 28).

Note: The console can display speed and distance in either miles or kilometers. To find out which unit of measurement is selected or to change the unit of mea- surement, see THE INFORMATION MODE on page

23.For simplicity, all instructions in this section refer to miles.

HOW TO PERSONALIZE CONSOLE SETTINGS

The console has a user mode that allows you to desig- nate yourself as User 1 or User 2, enter user informa- tion before you begin exercising, and select console settings. The user information you enter will also be recorded and stored in the fitness journal, which allows you to view your workout history (see HOW TO VIEW THE FITNESS JOURNAL on page 22).

Follow the steps below to personalize console settings.

1.Insert the key into the console.

See HOW TO TURN ON THE POWER at the left.

2.Select the user mode.

To select the user mode, press the Enter button. The console can store information and keep track of workout history for two different users.

When you select the user mode, the word LOGIN will appear in the display for a few seconds and then the login menu will appear.

Important: To highlight options within a menu, press the up, down, left, or right Navigation buttons. To select options within a menu, press the Enter button.

Note: To exit the user mode at any time, press the Back button repeatedly until the manual mode is se- lected (see page 16). To re-enter the user mode from the manual mode, press the Enter button.

3.Enter user information.

To enter your user information, first highlight the SETUP option and press the Enter button. The setup menu will then appear in the display.

Next, highlight the SETUP USER 1 or SETUP USER 2 option and press the Enter button. The user infor- mation menu will then appear in the display.

14

Image 14
Contents Call TOLL-FREE QUESTIONS?Please do not Contact On the WEBTable of Contents Important Precautions Page Before YOU Begin Assembly Make sure that the power cord is unplugged Do not fully fold the Frame yet Be careful not to pinch the Upright WireGers do not fully tighten the Bolts yet Tighten the Nut the Wheel must turn freelyPower is Turned on Not Connected PROPERLY, the CON Sole MAY be Damaged WhenSee steps 4 and 6. Tighten the 3/8 x 4 1/2 BoltsSmall Screws PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the ConsoleSelect the user mode HOW to Turn on the PowerHOW to Personalize Console Settings Insert the key into the consoleSet the date and time Select a default user settingHOW to Identify Yourself AS User 1 or User Select the manual mode HOW to USE the Manual ModePersonalize console settings if desired Start the walking belt and adjust the speedMeasure your heart rate if desired Press the Start button to start the workout HOW to USE a Classic WorkoutSelect a preset classic workout HOW to USE AN Event Training Workout Select an event training workoutHOW to Create a Custom Workout Select one of the four custom workoutsHOW to USE a Custom Workout HOW to View the Fitness Journal Exit the user mode HOW to Reset the Fitness JournalSelect the user mode. See on Reset the fitness journal Information ModeOptional Chest Pulse Sensor HOW to USE the Stereo Sound SystemHOW to Adjust the Cushioning System HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USETroubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Page Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyR0108A Key No. Qty DescriptionQty Exploded Drawing A-Model No. PFTL97007.0 R0108A Exploded Drawing B-Model No. PFTL97007.0 R0108A Exploded Drawing C-Model No. PFTL97007.0 Exploded Drawing D-Model No. PFTL97007.0 R0108A Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty