ProForm PETL71707.0 manual Troubleshooting, Problem The power turns off during use

Page 19

TROUBLESHOOTING

Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, call the telephone number listed on the back cover of this manual.

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet. (See page 11.) If an ex-

tension cord is needed, use only a 3-conductor, 1 mm2

(14-gauge) cord that is no longer than 1.5

m (5 ft.). Important: The treadmill is not compatible with RCD-equipped outlets.

 

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c. Check the reset/off circuit breaker located on the

c

 

treadmill frame near the power cord. If the switch

 

protrudes as shown, the circuit breaker has

 

 

tripped. To reset the circuit breaker, wait for five

Tripped

Reset

minutes and then press the switch back in.

PROBLEM: The power turns off during use

 

 

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c. Remove the key from the console. Reinsert the key into the console.

d. If the treadmill still will not run, please see the front cover of this manual.

PROBLEM: The incline of the treadmill does not change correctly

SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re-

move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the

maximum incline level and then return to the minimum level. This will recalibrate the incline system.

PROBLEM: The displays of the console do not function properly

 

 

 

SOLUTION: a. Remove the key from the console and UNPLUG

a

72

 

THE POWER CORD. With the help of a second

 

person, carefully tip the Uprights (71, 72) down.

 

 

 

There may be two Hood Screws (102) in the bottom

 

 

 

of the Belly Pan (66). If there are, remove them.

 

 

 

Then, raise the Uprights. Note: A Phillips screw-

71

 

 

driver with a shaft at least 5 in. (13 cm) long is re-

 

 

quired.

 

 

 

 

 

66

102

 

 

102

 

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Model No. PETL71707.0 Serial No QUESTIONS?Table of Contents Important Precautions Page Before YOU Begin Make sure that the power cord is unplugged AssemblyRepeat this step on the other side Wheel must turn freely Do not overtighten the Nut the Base Wheel must turn freely Careful not to pinch the Upright WireTighten the Bolts yet Not fully fold the Frame yetScrews and then tighten them This step is completed Sleeve to make sure that it is locked intoPlace Have a second person hold the Frame untilPRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Tightened before using the power cordFeatures of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerInsert the key into the console Distance/Incline dis When you are finished exercising, removeAdjust the incline of the treadmill to the lowest Time display-WhenMonitor your progress with the matrix and the displays HOW to USE a Preset WorkoutSelect a preset workout Customize your workout if desiredOptional Chest Pulse Sensor Information ModeHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingProblem The walking belt slows when walked on Problem Solution Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesKey No. Qty Description Part LIST-Model No. PETL71707.0Exploded Drawing A-Model No. PETL71707.0 R1207A Exploded Drawing B-Model No. PETL71707.0 R1207A Exploded Drawing C-Model No. PETL71707.0 R1207A Exploded Drawing D-Model No. PETL71707.0 R1207A Recycling Information Ordering Replacement Parts
Top Page Image Contents