ProForm PETL71707.0 manual Assembly, Make sure that the power cord is unplugged

Page 6

ASSEMBLY

Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill perfor- mance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires the included hex keys and your own Phillips screwdriver

and

adjustable wrench

.

 

Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The number after the parentheses is the quantity needed for assembly. Note: If a part is not in the parts bag, check to see if it is preattached to one of the parts to be assembled. To avoid damaging plastic parts, do not use power tools for assembly. Extra hardware may be included.

3/4" Screw (10)–8

3/8" Star

5/16" Star

3/8" Nut (8)–3

Base Pad Spacer

Washer (9)–4

Washer (7)–4

(25)–2

 

 

 

1" Tek Screw (56)–4

 

3/8" x 2" Bolt (4)–3

 

 

5/16" x 1" Bolt (5)–4

3/8" x 4" Bolt (6)–4

 

1. Make sure that the power cord is unplugged.

1

 

 

Remove the 3/8" Nut (8), the 3/8" x 2" Bolt (4),

 

 

 

and the shipping bracket (A) from the Base (80).

 

 

 

Repeat this step on the other side of the

 

 

 

treadmill. Discard the shipping brackets. The

 

 

 

Nuts and Bolts will be used later.

 

 

80

 

 

4 A

 

8

 

 

 

 

 

6

 

 

Image 6
Contents QUESTIONS? Model No. PETL71707.0 Serial NoTable of Contents Important Precautions Page Before YOU Begin Assembly Make sure that the power cord is unpluggedRepeat this step on the other side Wheel must turn freely Not fully fold the Frame yet Careful not to pinch the Upright WireTighten the Bolts yet Do not overtighten the Nut the Base Wheel must turn freelyScrews and then tighten them Have a second person hold the Frame until Sleeve to make sure that it is locked intoPlace This step is completedTightened before using the power cord Operation and AdjustmentHOW to Plug in the Power Cord PRE-LUBRICATED Walking BeltConsole Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeInsert the key into the console Time display-When When you are finished exercising, removeAdjust the incline of the treadmill to the lowest Distance/Incline disCustomize your workout if desired HOW to USE a Preset WorkoutSelect a preset workout Monitor your progress with the matrix and the displaysInformation Mode Optional Chest Pulse SensorHOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Problem Solution Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyPart LIST-Model No. PETL71707.0 Key No. Qty DescriptionExploded Drawing A-Model No. PETL71707.0 R1207A Exploded Drawing B-Model No. PETL71707.0 R1207A Exploded Drawing C-Model No. PETL71707.0 R1207A Exploded Drawing D-Model No. PETL71707.0 R1207A Ordering Replacement Parts Recycling Information