ProForm 590 lt user manual Assembly

Page 6

ASSEMBLY

To hire an authorized service technician to assemble the treadmill, call 1-800-445-2480.

Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill perfor- mance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires the included hex keys and your own Phillips screwdriver

,

adjustable wrench

, and scissors

.

 

Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The number after the parentheses is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it is preattached to one of the parts to be assembled. To avoid damaging plastic parts, do not use power tools for assem- bly. Extra hardware may be included.

M8 Star

M10 Star

#8 x 1/2" Ground

#8 x 3/4"

#8 x 1" Tek

#10 x 3/4"

Screw (29)–1

Screw (1)–6

Screw (2)–4

Screw (114)–2

Washer (9)–4

Washer (8)–4

 

 

 

 

 

 

 

 

3/8" x 1 1/2" Bolt (5)–1

3/8" x 1 3/4" Bolt (6)–1

Base Foot Spacer

M10 Locknut

M8 x 25mm

 

 

(36)–2

 

M10 x 50mm Bolt (26)–2

(94)–2

 

 

Bolt (4)–4

Bolt Spacer (98)–4

 

 

M10 x 96mm Bolt (7)–4

 

6

Image 6
Contents Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT QUESTIONS?Model No. PFTL99909.0 Serial No On the WEBTable of Contents Important Precautions Cord immediately after use, before cleaning Before YOU Begin Assembly Page Ful not to pinch the Wire Harness Do not overtighten the Locknut the Wheel Must turn freelyTouch the Upright do not fully tighten Bolts yet Do not fully fold the Frame yet Do not overtighten the Locknut Wheel must turn freelyTighten the Bolts yet Be Damaged When the Power is Nected PROPERLY, the Console MAYTurned on See steps 5 and 8. Tighten the M10 x 96mm Bolts Attach the other Cross Walk Arm 82 as de- scribed above Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeInsert the key into the console Measure your heart rate if desired Turn on the fan if desiredHOW to USE a Preset Workout Information Mode HOW to USE the Cross Walk ArmsHOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingProblem The power does not turn on Compatible with GFCI-equipped outletsProblem The walking belt slows when walked on TopProblem Solution Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyR0209A Key No. Qty. DescriptionDescription Exploded Drawing A-Model No. PFTL99909.0 R0209A Exploded Drawing B-Model No. PFTL99909.0 R0209A Exploded Drawing C-Model No. PFTL99909.0 R0209A Exploded Drawing D-Model No. PFTL99909.0 R0209A Ordering Replacement Parts Limited WarrantyIcon Health & Fitness, Inc., 1500 S W., Logan, UT