ProForm 590 lt user manual HOW to Turn on the Power, HOW to USE the Manual Mode

Page 16
Reset
Position

HOW TO TURN ON THE POWER

IMPORTANT: If the treadmill has been exposed to cold temperatures, allow it to warm to room tem- perature before turning on the power. If you do not do this, you may damage the console displays or other electrical components.

Plug in the power cord (see page 14). Next, locate the reset/off circuit breaker on the treadmill frame near the power cord. Switch the circuit breaker to the reset position.

IMPORTANT: The console features a display demo mode, designed to be used if the treadmill is dis- played in a store. If the displays light as soon as you plug in the power cord and switch the reset/off circuit breaker to the reset position, the demo mode is turned on. To turn off the demo mode, hold down the Stop button for a few seconds. If the displays remain lit, see THE INFORMATION MODE on page 19 to turn off the demo mode.

Next, stand on the foot rails of the treadmill. Find the clip attached to the key (see the drawing on page 15) and slide the clip onto the waistband of your clothes.

Then, insert the key into the console. After a moment, the displays will light. IMPORTANT: In an emergency situation, the key can be pulled from the console, causing the walking belt to slow to a stop. Test the clip by carefully taking a few steps backward; if the key is not pulled from the console, adjust the posi- tion of the clip.

HOW TO USE THE MANUAL MODE

1.Insert the key into the console.

See HOW TO TURN ON THE POWER above.

2.Select the manual mode. When the key is inserted, the manual mode will be selected. If you have se- lected a workout, press either of the Workout but- tons repeatedly until only zeros appear in the displays.

3.Start the walking belt.

To start the walking belt, press the Start button, the Speed increase button, or one of the ten numbered speed buttons.

If you press the Start button or the Speed increase button, the walking belt will begin to move at 1 mph. As you exercise, change the speed of the walking belt as desired by pressing the Speed increase and decrease buttons. Each time you press one of the buttons, the speed setting will change by 0.1 mph; if you hold down one of the buttons, the speed setting will change in increments of 0.5 mph. If you press one of the ten numbered speed but- tons, the walking belt will gradually change speed until it reaches the selected speed setting.

To stop the walking belt, press the Stop button. The time will begin to flash in the display. To restart the walking belt, press the Start button, the Speed increase button, or one of the ten numbered speed buttons.

4.Change the incline of the treadmill as desired. To change the incline of the treadmill, press the Incline increase and decrease buttons. Each time you press one of the buttons, the incline setting will change by 0.5 percent; if you hold down a button, the incline setting will change quickly.

5.Follow your progress with the displays. When you select the

manual mode, a track representing 1/4 mile

(400 meters) will appear in the matrix. As you walk or run on the tread-

mill, the indicators around the track will appear in succession until the entire track appears. The track will then disappear and the indicators will again begin to appear in succession.

16

Image 16
Contents QUESTIONS? Model No. PFTL99909.0 Serial NoMon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT On the WEBTable of Contents Important Precautions Cord immediately after use, before cleaning Before YOU Begin Assembly Page Do not overtighten the Locknut the Wheel Must turn freely Ful not to pinch the Wire HarnessTouch the Upright do not fully tighten Bolts yet Do not fully fold the Frame yet Do not overtighten the Locknut Wheel must turn freelyTighten the Bolts yet Nected PROPERLY, the Console MAY Be Damaged When the Power isTurned on See steps 5 and 8. Tighten the M10 x 96mm Bolts Attach the other Cross Walk Arm 82 as de- scribed above HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleHOW to USE the Manual Mode HOW to Turn on the PowerInsert the key into the console Measure your heart rate if desired Turn on the fan if desiredHOW to USE a Preset Workout Information Mode HOW to USE the Cross Walk ArmsHOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE Troubleshooting Problem The power does not turn onProblem The power turns off during use Compatible with GFCI-equipped outletsProblem The walking belt slows when walked on TopProblem Solution Exercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencyR0209A Key No. Qty. DescriptionDescription Exploded Drawing A-Model No. PFTL99909.0 R0209A Exploded Drawing B-Model No. PFTL99909.0 R0209A Exploded Drawing C-Model No. PFTL99909.0 R0209A Exploded Drawing D-Model No. PFTL99909.0 R0209A Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT