PART | R0706A | ||||
Key No. | Qty. | Description | Key No. | Qty. | Description |
1 | 1 | Frame | 37 | 1 | Right Pedal |
2 | 1 | Front Stabilizer | 38 | 1 | Right Pedal Strap |
3 | 1 | Rear Stabilizer | 39 | 1 | Flywheel |
4 | 1 | Left Side Shield | 40 | 1 | Left Pedal |
5 | 1 | Right Side Shield | 41 | 1 | Left Pedal Strap |
6 | 1 | Handlebar Post | 42 | 2 | Stabilizer Endcap |
7 | 1 | Handlebar | 43 | 1 | Flywheel Spacer |
8 | 1 | Bookrack | 44 | 1 | Reed Switch/Wire |
9 | 1 | Console | 45 | 1 | Pulse Sensor Assembly |
10 | 2 | Handlebar Foam | 46 | 1 | Reed Switch Clamp |
11 | 1 | Seat Post | 47 | 2 | M10 x 60mm Button Bolt |
12 | 1 | Seat | 48 | 6 | M10 Nylon Locknut |
13 | 2 | Round Collar | 49 | 1 | Idler Arm Assembly |
14 | 2 | Round Bushing | 50 | 1 | Long Spacer |
15 | 2 | Handlebar Endcap | 51 | 1 | Spring |
16 | 1 | Upper Wire Harness | 52 | 1 | M6 x 50mm Bolt |
17 | 2 | Wheel | 53 | 1 | Small Pulley |
18 | 1 | Magnet | 54 | 1 | Flywheel Washer |
19 | 7 | M8 x 25mm Button Screw | 55 | 1 | Resistance Motor |
20 | 2 | M4 x 25mm Screw | 56 | 5 | M8 Nylon Locknut |
21 | 16 | M4 x 16mm Screw | 57 | 4 | M5 Washer |
22 | 1 | “C” Magnet | 58 | 1 | M8 x 40mm Screw |
23 | 1 | 1" x 2" Endcap | 59 | 2 | M4 x 19mm Screw |
24 | 1 | Lower Wire Harness | 60 | 2 | M6 Nut |
25 | 2 | M4 x 12mm Screw | 61 | 4 | M6 x 13mm Button Screw |
26 | 2 | M6 x 8mm Screw | 62 | 2 | M10 x 92mm Carriage Bolt |
27 | 2 | Rear Stabilizer Endcap | 63 | 1 | Water Bottle Holder |
28 | 11 | M8 Split Washer | 64 | 2 | M10 x 105mm Carriage Bolt |
29 | 2 | Leveling Pad | 65 | 1 | Resistance Cable |
30 | 5 | M4 x 38mm Screw | 66 | 1 | Wiring Anchor |
31 | 1 | Seat Knob | 67 | 4 | M6 x 18mm Bolt |
32 | 1 | Crank Bearing Set | 68 | 1 | Nylon Zip Tie |
33 | 1 | Crank Assembly | 69 | 1 | Belt |
34 | 1 | Pulley | # | 1 | User’s Manual |
35 | 2 | Pillow Block Set | # | 1 | Hex Key |
36 | 2 | Snap Ring | # | 2 | Assembly Tool |
Note: “#” indicates a
22