Suunto None manual Setting the units, Setting the backlight, Setting the tones, AC water contacts

Page 12

ADJUST WITH UP AND

DOWN BUTTONS. ACCEPT

WITH SELECT BUTTON.

4.1.4. Setting the units

In the UNITS SETTING mode you can choose to have the units displayed in either the metric or imperial system - meters/feet, Celsius/Fahrenheit etc.

ADJUST WITH UP AND

DOWN BUTTONS. ACCEPT

WITH SELECT BUTTON.

4.1.5. Setting the backlight

Use the BACKLIGHT SETTING mode to turn the backlight on or off and to define how long it stays on for (5, 10, 20, 30, or 60 seconds). When the backlight is turned off, it does not illuminate when an alarm sounds.

ADJUST WITH UP AND

DOWN BUTTONS. ACCEPT

WITH SELECT BUTTON.

4.1.6. Setting the tones

The TONE SETTING mode allows you to activate or deactivate the tones.

ADJUST WITH UP AND

DOWN BUTTONS. ACCEPT

WITH SELECT BUTTON.

NOTE	When the tones are off, there are no audible alarms.

4.2. AC water contacts

The water and data transfer contact is located on the rear of the case. When submerged, the water contact poles are connected by the conductivity of the water and the “AC” symbol appears on the display. The AC text is shown until the water contact deactivates.

12

Image 12

Contents COBRA3 Time Tank pressure Before Diving Intellectual Property Welcome to the World of Suunto Diving Instruments Before DIVING. Make sure that you fully understand the use Serious injury or deathNot for Professional USE! Suunto dive computers are That tend to increase the risk of decompression illness DCIDives That Require Decompression Stops are not Nitrox mode, as well as from AIR or Nitrox mode to Gauge Mode even during the no-fly timeBatteries. Recycle or dispose of used batteries properly Before the instrument has counted down the no-fly timeButton symbols and functions Symbol Button Press Main functionsSuunto AT a Glance Navigating in the menusDown Time mode settings Setting the alarmSetting the time Setting the dateSetting the units Setting the backlightSetting the tones AC water contactsLearning how to use your compass Displays by pressing the UP/DOWN buttonsCompass display Locking a bearingSymbol Explanation Compass settingsCalibration Declination Time-outBefore Diving Suunto RGBM/Deep Stop AlgorithmEmergency ascents Dive computer limitationsAudible and visual alarms Alarm typePreset alarm types Alarm type NitroxAlarm type Alarm reason Alarm is activatedError conditions Omitted decompressionConnecting Suunto Cobra3 to a regulator Dive mode settingsSetting the depth alarm Setting the dive-time alarmSetting the nitrox values Setting the personal/altitude adjustmentsBottom time, for example Are stored until changedSetting the sample rate Setting the Safety Stops/Deep StopsSetting the Rgbm values Setting the tank pressure alarmAccessing Dive mode Dive mode activationActivation and pre-checks Battery power indication Alt. adjustment value Altitude rangeDiving at altitude How the Altitude value is setPersonal adjustments Personal Condition Desired tables Adjustment ValueRgbm setting Desired Tables Effect Safety Stops Recommended Safety StopsMandatory Safety Stops Deep stops Diving in AIR mode DIVEair DivingOrder to perform the necessary dive pre-checks Basic dive dataBookmark Tank pressure dataAscent rate indicator Low Air Pressure WarningsDecompression dives Ceiling, ceiling zone, floor and decompression range Display below the floorDisplay above the floor Display at the ceiling zoneDisplay above the ceiling Diving in Nitrox mode DIVEnitrox Before diving in Nitrox modeDefault nitrox settings Oxygen displaysDiving in Gauge mode DIVEgauge Oxygen limit fraction OLFGas change and multiple breathing gas mixes Gauge mode does not provide decompression information There is no ascent rate monitoring in the Gauge modeModes before the no fly time has counted down Alarms Symbol on display After DivingSurface interval Dive numberingPlan mode Dive Planning mode PLANnodecFlying after diving Simulation Mode PLANsimulator ModeDive numbering shown during dive planning Dive SimulatorMemory mode Dive logbook MEMLogbookProviding that the battery has been replaced according to InstructionsDive series if the no-fly time has not ended. See .2. Dive Numbering for further informationUnit and the downloadable Suunto Dive Manager software Suunto Dive Manager SDMPage Care and Maintenance of MY Suunto Diving Computer Water Contacts and Push ButtonsFAQs Battery replacement and strap kits must be usedWarranty Battery Replacement Battery kitReplacing the battery Required toolsBattery compartment lid, indicating a leak Technical Data Rgbm Suunto Rgbm adaptive decompressionDiver Attention Symbol Advice to Extend Surface Interval No-decompression limitsAltitude diving Oxygen exposureIntellectual Property Copyright TrademarkPatent notice Disclaimers User’s responsibility12.2. CE Warranty Period Exclusions and LimitationsAccess to Suunto warranty service Other important noticesLimitation of Liability Page Disposal of the Device Glossary EAD EANNoaa Customer Service Contacts CopyrightTWO Year Warranty Suunto Oy 9/2008, 10/2008, 11/2008