Suunto None manual Memory mode, Dive logbook MEMLogbook

Page 38

PRESS UP OR

DOWN BUTTONS

TO DESCEND OR

ASCEND.

The mode can also be used to add the desired surface intervals for dive simulations. Add the desired surface interval increments to the present surface interval by pressing the UP and DOWN buttons.

ADD SURFACE TIME IN

15 MINUTES INCREMENTS.

7.6. MEMORY mode

The memory options include a dive logbook (MEMLogbook) and dive history (MEMHistory).

The dive time and date are registered in the Logbook memory. Always check before diving that the time and date are correctly set, especially after traveling between different time zones.

7.6.1. Dive logbook (MEMLogbook)

The Suunto Cobra3 has a very sophisticated, high capacity Logbook and Profile Memory. The data is recorded in the profile memory based on the selected sample rate.

The END OF LOGS text is displayed between the oldest and most recent dive. The following information will be shown on three pages:

Image 38

Contents COBRA3 Time Tank pressure Before Diving Intellectual Property Welcome to the World of Suunto Diving Instruments Not for Professional USE! Suunto dive computers are Before DIVING. Make sure that you fully understand the useSerious injury or death That tend to increase the risk of decompression illness DCIDives That Require Decompression Stops are not Batteries. Recycle or dispose of used batteries properly Nitrox mode, as well as from AIR or Nitrox mode to GaugeMode even during the no-fly time Before the instrument has counted down the no-fly timeSuunto AT a Glance Button symbols and functionsSymbol Button Press Main functions Navigating in the menusDown Setting the time Time mode settingsSetting the alarm Setting the dateSetting the tones Setting the unitsSetting the backlight AC water contactsCompass display Learning how to use your compassDisplays by pressing the UP/DOWN buttons Locking a bearingCalibration Symbol ExplanationCompass settings Declination Time-outEmergency ascents Before DivingSuunto RGBM/Deep Stop Algorithm Dive computer limitationsPreset alarm types Alarm type Audible and visual alarmsAlarm type NitroxError conditions Alarm type Alarm reasonAlarm is activated Omitted decompressionSetting the depth alarm Connecting Suunto Cobra3 to a regulatorDive mode settings Setting the dive-time alarmBottom time, for example Setting the nitrox valuesSetting the personal/altitude adjustments Are stored until changedSetting the Rgbm values Setting the sample rateSetting the Safety Stops/Deep Stops Setting the tank pressure alarmActivation and pre-checks Accessing Dive modeDive mode activation Diving at altitude Battery power indicationAlt. adjustment value Altitude range How the Altitude value is setRgbm setting Desired Tables Effect Personal adjustmentsPersonal Condition Desired tables Adjustment Value Mandatory Safety Stops Safety StopsRecommended Safety Stops Deep stops Order to perform the necessary dive pre-checks Diving in AIR mode DIVEairDiving Basic dive dataBookmark Tank pressure dataDecompression dives Ascent rate indicatorLow Air Pressure Warnings Ceiling, ceiling zone, floor and decompression range Display below the floorDisplay above the ceiling Display above the floorDisplay at the ceiling zone Default nitrox settings Diving in Nitrox mode DIVEnitroxBefore diving in Nitrox mode Oxygen displaysGas change and multiple breathing gas mixes Diving in Gauge mode DIVEgaugeOxygen limit fraction OLF Modes before the no fly time has counted down Gauge mode does not provide decompression informationThere is no ascent rate monitoring in the Gauge mode Surface interval Alarms Symbol on displayAfter Diving Dive numberingFlying after diving Plan modeDive Planning mode PLANnodec Dive numbering shown during dive planning Simulation Mode PLANsimulatorMode Dive SimulatorMemory mode Dive logbook MEMLogbookDive series if the no-fly time has not ended. See .2. Dive Providing that the battery has been replaced according toInstructions Numbering for further informationUnit and the downloadable Suunto Dive Manager software Suunto Dive Manager SDMPage Care and Maintenance of MY Suunto Diving Computer Water Contacts and Push ButtonsWarranty FAQsBattery replacement and strap kits must be used Replacing the battery Battery ReplacementBattery kit Required toolsBattery compartment lid, indicating a leak Technical Data Rgbm Suunto Rgbm adaptive decompressionDiver Attention Symbol Advice to Extend Surface Interval No-decompression limitsAltitude diving Oxygen exposurePatent notice Intellectual PropertyCopyright Trademark 12.2. CE DisclaimersUser’s responsibility Warranty Period Exclusions and LimitationsLimitation of Liability Access to Suunto warranty serviceOther important notices Page Disposal of the Device Glossary EAD EANNoaa Customer Service Contacts CopyrightTWO Year Warranty Suunto Oy 9/2008, 10/2008, 11/2008