Suunto None Care and Maintenance of MY Suunto Diving Computer, Water Contacts and Push Buttons

Page 42

8. CARE AND MAINTENANCE OF MY SUUNTO DIVING COMPUTER

The SUUNTO dive computer is a sophisticated precision instrument. Although it is designed to withstand the rigors of scuba diving, you must treat it with the same proper care and caution as any other precision instrument.

•WATER CONTACTS AND PUSH BUTTONS

Contamination or dirt on the water contacts/connector or push buttons may prevent the automatic activation of the Dive Mode and cause problems during the data transfer. Therefore, it is important that the water contacts and push buttons are kept clean. If the water contacts are active (AC text remains on display) or the Dive Mode activates on its own, the reason for this is probably contamination or invisible marine growth, which may create an electric current between the contacts. It is important that the dive computer is carefully washed in fresh water after the day’s diving is completed. The contacts can be cleaned with fresh water and, if necessary, a mild detergent and a soft brush. Sometimes it might be necessary to remove the instrument from the protective boot for cleaning.

•CARE OF YOUR DIVE COMPUTER

•NEVER try to open the case of the dive computer.

•Have your dive computer serviced every two years or after 200 dives (whichever comes first) by an authorized dealer or distributor. This service will include a general operational check, replacement of the battery, and water resistance check. The service requires special tools and training. Therefore, it is advisable to contact an authorized SUUNTO dealer or distributor for the biennial service. Do not attempt to do any servicing that you are not sure of.

•Should moisture appear inside the case or battery compartment, immediately have the instrument checked by your SUUNTO dealer or distributor.

•Should you detect scratches, cracks or other such flaws on the display that may impair its durability, immediately have it replaced by your SUUNTO dealer or distributor.

•Wash and rinse the unit in fresh water after every use.

•Protect the unit from shock, extreme heat, direct sunlight, and chemical attack. The dive computer cannot withstand the impact of heavy objects like scuba cylinders, nor chemicals like gasoline, cleaning solvents, aerosol sprays, adhesive agents, paint, acetone, alcohol, etc. Chemical reactions with such agents will damage the seals, case and finish.

•Store your dive computer in a dry place when you are not using it.

•The dive computer will display a battery symbol as a warning when the power gets too low. When this happens, the instrument should not be used until the battery has been replaced.

•Do not fasten the strap of your dive computer too tightly. You should be able to insert your finger between the strap and your wrist. Shorten the strap by cutting it if you do not expect to need the extra length.

•MAINTENANCE

The instrument should be soaked, thoroughly rinsed with fresh water, then dried with a soft towel after each dive. Make sure that all salt crystals and sand particles have been flushed out. Check the display and the transparent battery compartment cover for possible moisture or water. DO NOT use the dive computer if you detect any moisture or water inside. In order to limit corrosion damage, remove the battery and moisture from the battery compartment. Contact an authorized Suunto dealer for battery replacement or other service.

CAUTION!

•Do not use compressed air to blow water off the unit.

•Do not use solvents or other cleaning fluids that might cause damage.

•Do not test or use the dive computer in pressurized air.

•WATER RESISTANCE INSPECTION

42

Page 41 Page 43
Image 42
Page 41 Page 43
Contents COBRA3 Time Tank pressure Before Diving Intellectual Property Welcome to the World of Suunto Diving Instruments Not for Professional USE! Suunto dive computers are Before DIVING. Make sure that you fully understand the useSerious injury or death That tend to increase the risk of decompression illness DCIDives That Require Decompression Stops are not Batteries. Recycle or dispose of used batteries properly Nitrox mode, as well as from AIR or Nitrox mode to GaugeMode even during the no-fly time Before the instrument has counted down the no-fly timeSuunto AT a Glance Button symbols and functionsSymbol Button Press Main functions Navigating in the menusDown Setting the time Time mode settingsSetting the alarm Setting the dateSetting the tones Setting the unitsSetting the backlight AC water contactsCompass display Learning how to use your compassDisplays by pressing the UP/DOWN buttons Locking a bearingSymbol Explanation Compass settingsCalibration Declination Time-outEmergency ascents Before DivingSuunto RGBM/Deep Stop Algorithm Dive computer limitationsPreset alarm types Alarm type Audible and visual alarmsAlarm type NitroxError conditions Alarm type Alarm reasonAlarm is activated Omitted decompressionSetting the depth alarm Connecting Suunto Cobra3 to a regulatorDive mode settings Setting the dive-time alarmBottom time, for example Setting the nitrox valuesSetting the personal/altitude adjustments Are stored until changedSetting the Rgbm values Setting the sample rateSetting the Safety Stops/Deep Stops Setting the tank pressure alarmAccessing Dive mode Dive mode activationActivation and pre-checks Diving at altitude Battery power indicationAlt. adjustment value Altitude range How the Altitude value is setPersonal adjustments Personal Condition Desired tables Adjustment ValueRgbm setting Desired Tables Effect Safety Stops Recommended Safety StopsMandatory Safety Stops Deep stops Order to perform the necessary dive pre-checks Diving in AIR mode DIVEairDiving Basic dive dataBookmark Tank pressure dataAscent rate indicator Low Air Pressure WarningsDecompression dives Ceiling, ceiling zone, floor and decompression range Display below the floorDisplay above the floor Display at the ceiling zoneDisplay above the ceiling Default nitrox settings Diving in Nitrox mode DIVEnitroxBefore diving in Nitrox mode Oxygen displaysDiving in Gauge mode DIVEgauge Oxygen limit fraction OLFGas change and multiple breathing gas mixes Gauge mode does not provide decompression information There is no ascent rate monitoring in the Gauge modeModes before the no fly time has counted down Surface interval Alarms Symbol on displayAfter Diving Dive numberingPlan mode Dive Planning mode PLANnodecFlying after diving Dive numbering shown during dive planning Simulation Mode PLANsimulatorMode Dive SimulatorMemory mode Dive logbook MEMLogbookDive series if the no-fly time has not ended. See .2. Dive Providing that the battery has been replaced according toInstructions Numbering for further informationUnit and the downloadable Suunto Dive Manager software Suunto Dive Manager SDMPage Care and Maintenance of MY Suunto Diving Computer Water Contacts and Push ButtonsFAQs Battery replacement and strap kits must be usedWarranty Replacing the battery Battery ReplacementBattery kit Required toolsBattery compartment lid, indicating a leak Technical Data Rgbm Suunto Rgbm adaptive decompressionDiver Attention Symbol Advice to Extend Surface Interval No-decompression limitsAltitude diving Oxygen exposureIntellectual Property Copyright TrademarkPatent notice Disclaimers User’s responsibility12.2. CE Warranty Period Exclusions and LimitationsAccess to Suunto warranty service Other important noticesLimitation of Liability Page Disposal of the Device Glossary EAD EANNoaa Customer Service Contacts CopyrightTWO Year Warranty Suunto Oy 9/2008, 10/2008, 11/2008
Top Page Image Contents