JVC RX-7520VBK manual Basic Settings, Setting the Speaker Information Remote

Page 19

Basic Settings

English

Selecting the Video Input

Remote

Terminal

NOT

This receiver is equipped with the component video input terminals for the DVD player which give you higher picture quality. When you use the component video input terminals for the DVD player, change the video input terminal setting.

Before you start, remember....

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

1 Press SETTING repeatedly until

 

 

ST

SETTING

“VIDEO IN DVD ” or “VIDEO IN

 

 

 

 

 

 

 

 

VCR ” appears on the display.

 

 

•Select “VIDEO IN DVD” to select the video input terminal for the DVD player and “VIDEO IN VCR” for the VCR.

SPK 1

DIGITAL AUTO L C R

LINEAR PCM

CH-

After 2 seconds, the display changes to show the current setting.

“NO” for the subwoofer, “LARGE” for the front speakers, and “SMALL” for the center and rear speakers are initial settings. To get best possible sound, change the subwoofer and speaker settings to fit your listening conditions.

Setting the Speaker Information Remote

NOT

To obtain the best possible sound or effect from Surround modes (see pages 26 to 29), register the following speakers and subwoofer information after all connections are completed.

The following are items you can set:

•Subwoofer information—SUBWOOFER

•Speaker size—FRNT SP, CNTR SP, REAR SP

•Speaker distance—UNIT, FRNT DIS, CNTR DIS, REAR DIS

•Crossover frequency—CROSS

•Low frequency effect attenuator—LFE ATT

•Dynamic range compression—D. COMP

Before you start, remember....

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

2 Press CONTROL UP 5/DOWN ∞ CONTROL

DOWN UP

to select the appropriate type of the video input terminal.

•Each time you press the button, the display changes as follows:

 

COMPONENT

 

S/C

 

 

 

(Component)

(S-video/Composite)

 

 

COMPONENT : Select this when you connect the DVD

 

player or VCR to the component video

 

input terminals.

S/C

: Select this when you connect the DVD player

 

or VCR to the S-video or composite video

 

input terminal.

 

 

 

 

Note:

Without changing the video input terminal setting, you can see the picture through the video input terminals, but cannot use the AV COMPU LINK remote control system correctly (see page 32).

Subwoofer information

Register whether you have connected a subwoofer or not.

1 Press SETTING repeatedly until

 

 

ST

SETTING

“SUBWOOFER” (with the current

 

 

 

 

 

 

 

 

setting)* appears on the display.

 

 

 

 

 

 

 

SPK 1

 

 

 

DIGITAL AUTO L C R

 

 

 

LINEAR PCM S.WFR LFE

 

 

 

CH-

 

 

 

 

 

 

*“NO” is the initial setting. If you have already changed the setting, “YES” will be shown.

2 Press CONTROL UP 5/DOWN ∞ to CONTROL

DOWN UP

register whether you have connected a subwoofer or not.

•Each time you press the button, the subwoofer setting alternates between “YES” and “NO.”

YES : Select this when you have connected a subwoofer. You can adjust the subwoofer output level

(see page 20).

NO : Select this when you have not connected or have disconnected a subwoofer.

16

Page 18 Page 20
Image 19
Page 18 Page 20
Contents RX-7520VBK For U.S.A Mises en garde, précautions et indications diversesRX-7520VBK For Canada/pour le Canada For Canada/pour Le CanadaTable of Contents Parts Identification Remote ControlFront Panel Replace the cover Before Installation Putting Batteries in the Remote ControlChecking the Supplied Accessories Getting StartedFM antenna connection Connecting the FM and AM AntennasGetting Started AM antenna connectionConnection diagram Connecting the SpeakersSpeaker layout diagram Connecting the front speakersAnalog connections Audio component connections Connecting Audio/Video ComponentsConnecting the rear and center speakers Connecting the subwoofer speakerVCR Video component connectionsCassette deck or CD recorder If your audio components have a Compu Link jackDVD player For enjoying DVD Multi Playback ModeDVD player Digital input terminals Connecting the Power CordPlug the power cord into an AC outlet Digital connectionsAudio Turning On the Power Selecting the Source to PlayBasic Operations STANDBY/ONOn the front panel Adjusting the VolumeFrom the remote control Changing the source nameTurning Off the Sounds Temporarily-Muting Turning Off the Power With the Sleep TimerHeadphone mode Basic OperationsFor recording Basic adjustment auto memorySignal and speaker indicators on the display Speaker indicators light up whenSelecting the Analog or Digital Input Mode Basic SettingsOn the front panel Press Control UP 5/DOWN ∞ toSelect Dolby Digital or DTS Surround while Digital Auto still remains on the displaySetting the Speaker Information Remote Basic SettingsSelect the appropriate speaker distance Press Setting repeatedly until Frnt ST SettingWith the current setting* appears on the display Select the unitPress Control UP 5/DOWN ∞ Select the low frequency effectAttenuator level Comp Dynamic rangeAdjusting the Front Speakers Sound AdjustmentsOutput Balance Adjusting the Subwoofer Output Level Sound AdjustmentsReinforcing the Bass Using Preset Tuning Tuning in Stations ManuallyTuner Operations Tuner Operations Selecting the FM Reception ModeTypical Multichannel 5.1 ch reproduction Creating Realistic Sound FieldsDolby Surround DTS Digital SurroundAll Channel Stereo reproduction DVD Multi Playback ModeCreating Realistic Sound Fields DAP Digital Acoustic Processor modes All Channel StereoSpeaker Layouts Available Surround modes About Relations between Speaker Layouts and Surround ModesTurning on or off the Surround modes Selecting the Surround modesIf you like to adjust sound, go to step Activate Surround modePress Surround ON/OFF to Press Test again to stop the test tone Set the analog or digital input mode forAdjust the speaker output levels -10 to +10 Source you like to hear and start playingUsing DAP Modes and All Channel Stereo To cancel DAP modes and All Channel Stereo Press Surround ON/OFF to activate Surround modePress Surround Mode repeatedly For DAP modes only Adjust the effect levelActivating DVD Multi Playback Mode Using DVD Multi Playback ModePress DVD Multi Synchronized Recording Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Press the play 3 button on the CD playerConnections 1 AV Compu Link Connection AV Compu Link Remote Control SystemConnections 2 Video Cable Connections One-Touch DVD Play Automatic Selection of TV’s Input ModeAutomatic Power On/Off One-Touch Video PlayTuner Sound AdjustmentOperating JVC’s Audio/Video Components Operating Audio ComponentsCassette deck CD changerCD recorder DVD menu operations Operating JVC’s Audio/Video ComponentsOperating Video Components DVD playerTry to operate your TV by pressing To change the transmittable signals for operating a TVIf there are more than one code listed for your brand of TV Operating Other Manufacturers’ Video EquipmentTry to operate your VCR by pressing To change the transmittable signals for operating a VCROperating Other Manufacturers’ Video Equipment Try to operate your Catv converter by pressingManufacturers’ codes for DVD player Codes Try to operate your DVD player by pressingPanasonic Philips Pioneer Sony Toshiba Yamaha Problem Possible Cause Solution TroubleshootingHarmonic distortion SpecificationsPer channel, min. RMS, driven into 8 Ω Hz to 20 kHz with no more than 0.8% totalGeneral SpecificationsFM tuner IHF AM tunerEN, FR 0202NHMMDWJEIN

RX-7520VBK specifications

The JVC RX-7520VBK is a well-regarded audio receiver that combines advanced technology with user-friendly features, making it an ideal choice for both audiophiles and casual listeners. This model is designed to enhance the home theater experience, delivering high-quality sound and versatility in connectivity options.

One of the standout features of the JVC RX-7520VBK is its powerful amplification system. With a robust output of 100 watts per channel, this receiver can handle large speakers and create an immersive audio experience. It supports various surround sound formats, including Dolby Digital and DTS, allowing users to enjoy movies, music, and games in rich detail and clarity.

In terms of connectivity, the RX-7520VBK is equipped with multiple inputs and outputs, ensuring compatibility with a range of devices. It includes several HDMI ports, which support high-definition video and audio, making it suitable for connecting modern gaming consoles, Blu-ray players, and streaming devices. The receiver also features component video inputs and composite video connections, allowing users to incorporate older devices seamlessly.

The JVC RX-7520VBK is designed to support various audio formats, including MP3 and WMA, ensuring versatility in playback options. For users looking to enhance their music experience, the receiver features a built-in equalizer with multiple presets, enabling fine-tuning of audio settings to match individual preferences and room acoustics.

Furthermore, this model offers advanced technologies such as Virtual Surround for enhancing audio spatialization in two-channel audio sources. This feature is particularly useful for creating a more cinematic experience when watching movies or enjoying music in stereo.

User-friendliness is a key aspect of the RX-7520VBK. The front panel features a clear display and buttons that are easy to navigate, while the included remote control offers convenient access to various settings and functions without needing to get up from the couch.

In summary, the JVC RX-7520VBK is a versatile and powerful receiver, ideal for those looking to create a comprehensive home theater system. With its strong amplification, extensive connectivity options, support for multiple audio formats, and user-friendly design, it stands as a solid choice in the realm of audio receivers. Whether for casual listening or a full cinematic experience, the RX-7520VBK promises to elevate any sound setup.
Top Page Image Contents