JVC RX-7520VBK manual Press Setting repeatedly until Frnt ST Setting, Select the unit

Page 20

Speaker size

Register the sizes of all the connected speakers.

When you change your speakers, register the information about the speakers again.

1Press SETTING repeatedly until “FRNT ST SETTING

SP (Front Speaker),” “CNTR SP (Center Speaker)” or “REAR SP (Rear Speaker)”

(with the current setting)* appears on the display.

SPK 1

DIGITAL AUTO L C R

LINEAR PCM S.WFR LFE

LS S RS

CH-

*“LARGE” is the initial setting for the front speakers and “SMALL” is for the center and rear speakers. If you have already changed the setting, another size will be shown.

2 Press CONTROL UP 5/DOWN to CONTROL

DOWN UP

select the appropriate item about the speaker selected in the above step.

Each time you press the button, the display changes as follows:

LARGE SMALL

NONE

LARGE : Select this when the speaker size is relatively large. (See “Notes” below.)

SMALL : Select this when the speaker size is relatively small. (See “Notes” below.)

NONE : Select this when you have not connected a speaker. (Not selectable for the front speakers)

3Repeat steps 1 and 2 to select the appropriate items for other speakers.

Notes:

Keep the following comment in mind as reference when adjusting.

If the size of the cone speaker unit built in your speaker is greater than 12 cm (4 3/4 inches), select “LARGE,” and if it is smaller than 12 cm (4 3/4 inches), select “SMALL.”

If you have selected “NO” for the subwoofer setting, you can only select “LARGE” for the front speaker setting.

If you have selected “SMALL” for the front speaker setting, you cannot select “LARGE” for the center and rear speaker settings.

Speaker distance

Register the unit you use, then the speaker distance from your listening point.

If you have set the unit before, start from step 3.

Speaker distance is not valid for the DVD MULTI playback mode.

1Press SETTING repeatedly until “UNIT” T SETTING

(with the current setting)* appears on the display.

 

SPK 1

 

DIGITAL AUTO

L

C

R

LINEAR PCM

S.WFR LFE

 

LS

S

RS

CH-

*“METER” is the initial setting. If you have already changed the setting, “FEET” will be shown.

2 Press CONTROL UP 5/DOWN to CONTROL

DOWN UP

select the unit.

• Each time you press the button, the setting alternates between “METER” and “FEET.”

METER : Speaker distance is shown in meters.

FEET : Speaker distance is shown in feet.

3Press SETTING repeatedly until “FRNT T SETTING

DIS (Front distance),” “CNTR DIS (Center distance)” or “REAR DIS (Rear distance)” (with the current setting)* appears on the display.

The display shows the current setting in the unit selected in

step 2.

*“3.0m” is the initial setting for meter and “10FT” is for feet. If you have already changed the setting, another value will be shown.

4 Press CONTROL UP 5/DOWN to CONTROL

DOWN UP

select the appropriate speaker distance.

• If you select “METER” in step 2, the value is changed from “0.3m” to “9.0m” by 0.3 m step.

If you select “FEET” in step 2, the value is changed from “1FT” to “30FT” by 1 foot step.

Left front

 

 

 

Right front

speaker

 

Center speaker

 

speaker

 

 

 

 

 

3.0 m

(10 feet)

2.7 m

(9 feet)

2.4 m

(8 feet)

2.1 m

(7 feet)

Left rear

Right rear

speaker

speaker

Example: In this case,

set “FRNT DIS” to “3.0m” or “10FT,” set “CNTR DIS” to “2.7m” or “9FT,” and set “REAR DIS” to “2.4m” or “8FT.”

Note:

If you have selected “NONE” for the center and rear speakers setting,

you cannot set the speaker distance for the center and rear speakers.

English

17

Image 20
Contents RX-7520VBK Mises en garde, précautions et indications diverses For U.S.AFor Canada/pour le Canada For Canada/pour Le Canada RX-7520VBKTable of Contents Front Panel Remote ControlParts Identification Before Installation Putting Batteries in the Remote Control Checking the Supplied AccessoriesGetting Started Replace the coverConnecting the FM and AM Antennas Getting StartedAM antenna connection FM antenna connectionConnecting the Speakers Speaker layout diagramConnecting the front speakers Connection diagramConnecting Audio/Video Components Connecting the rear and center speakersConnecting the subwoofer speaker Analog connections Audio component connectionsVideo component connections Cassette deck or CD recorderIf your audio components have a Compu Link jack VCRDVD player For enjoying DVD Multi Playback ModeDVD player Connecting the Power Cord Plug the power cord into an AC outletDigital connections Digital input terminalsTurning On the Power Selecting the Source to Play Basic OperationsSTANDBY/ON AudioAdjusting the Volume From the remote controlChanging the source name On the front panelTurning Off the Power With the Sleep Timer Headphone modeBasic Operations Turning Off the Sounds Temporarily-MutingBasic adjustment auto memory Signal and speaker indicators on the displaySpeaker indicators light up when For recordingBasic Settings Selecting the Analog or Digital Input ModePress Control UP 5/DOWN ∞ to Select Dolby Digital or DTSSurround while Digital Auto still remains on the display On the front panelBasic Settings Setting the Speaker Information RemotePress Setting repeatedly until Frnt ST Setting With the current setting* appears on the displaySelect the unit Select the appropriate speaker distanceSelect the low frequency effect Attenuator levelComp Dynamic range Press Control UP 5/DOWN ∞Output Balance Sound AdjustmentsAdjusting the Front Speakers Reinforcing the Bass Sound AdjustmentsAdjusting the Subwoofer Output Level Tuner Operations Tuning in Stations ManuallyUsing Preset Tuning Selecting the FM Reception Mode Tuner OperationsCreating Realistic Sound Fields Dolby SurroundDTS Digital Surround Typical Multichannel 5.1 ch reproductionDVD Multi Playback Mode Creating Realistic Sound FieldsDAP Digital Acoustic Processor modes All Channel Stereo All Channel Stereo reproductionAbout Relations between Speaker Layouts and Surround Modes Turning on or off the Surround modesSelecting the Surround modes Speaker Layouts Available Surround modesPress Surround ON/OFF to Activate Surround modeIf you like to adjust sound, go to step Set the analog or digital input mode for Adjust the speaker output levels -10 to +10Source you like to hear and start playing Press Test again to stop the test toneUsing DAP Modes and All Channel Stereo Press Surround ON/OFF to activate Surround mode Press Surround Mode repeatedlyFor DAP modes only Adjust the effect level To cancel DAP modes and All Channel StereoPress DVD Multi Using DVD Multi Playback ModeActivating DVD Multi Playback Mode Compu Link Remote Control System Remote Control through the Remote Sensor on the ReceiverPress the play 3 button on the CD player Synchronized RecordingConnections 2 Video Cable Connections AV Compu Link Remote Control SystemConnections 1 AV Compu Link Connection Automatic Selection of TV’s Input Mode Automatic Power On/OffOne-Touch Video Play One-Touch DVD PlaySound Adjustment Operating JVC’s Audio/Video ComponentsOperating Audio Components TunerCD recorder CD changerCassette deck Operating JVC’s Audio/Video Components Operating Video ComponentsDVD player DVD menu operationsTo change the transmittable signals for operating a TV If there are more than one code listed for your brand of TVOperating Other Manufacturers’ Video Equipment Try to operate your TV by pressingTo change the transmittable signals for operating a VCR Operating Other Manufacturers’ Video EquipmentTry to operate your Catv converter by pressing Try to operate your VCR by pressingPanasonic Philips Pioneer Sony Toshiba Yamaha Try to operate your DVD player by pressingManufacturers’ codes for DVD player Codes Troubleshooting Problem Possible Cause SolutionSpecifications Per channel, min. RMS, driven into 8 ΩHz to 20 kHz with no more than 0.8% total Harmonic distortionSpecifications FM tuner IHFAM tuner GeneralEN, FR 0202NHMMDWJEIN

RX-7520VBK specifications

The JVC RX-7520VBK is a well-regarded audio receiver that combines advanced technology with user-friendly features, making it an ideal choice for both audiophiles and casual listeners. This model is designed to enhance the home theater experience, delivering high-quality sound and versatility in connectivity options.

One of the standout features of the JVC RX-7520VBK is its powerful amplification system. With a robust output of 100 watts per channel, this receiver can handle large speakers and create an immersive audio experience. It supports various surround sound formats, including Dolby Digital and DTS, allowing users to enjoy movies, music, and games in rich detail and clarity.

In terms of connectivity, the RX-7520VBK is equipped with multiple inputs and outputs, ensuring compatibility with a range of devices. It includes several HDMI ports, which support high-definition video and audio, making it suitable for connecting modern gaming consoles, Blu-ray players, and streaming devices. The receiver also features component video inputs and composite video connections, allowing users to incorporate older devices seamlessly.

The JVC RX-7520VBK is designed to support various audio formats, including MP3 and WMA, ensuring versatility in playback options. For users looking to enhance their music experience, the receiver features a built-in equalizer with multiple presets, enabling fine-tuning of audio settings to match individual preferences and room acoustics.

Furthermore, this model offers advanced technologies such as Virtual Surround for enhancing audio spatialization in two-channel audio sources. This feature is particularly useful for creating a more cinematic experience when watching movies or enjoying music in stereo.

User-friendliness is a key aspect of the RX-7520VBK. The front panel features a clear display and buttons that are easy to navigate, while the included remote control offers convenient access to various settings and functions without needing to get up from the couch.

In summary, the JVC RX-7520VBK is a versatile and powerful receiver, ideal for those looking to create a comprehensive home theater system. With its strong amplification, extensive connectivity options, support for multiple audio formats, and user-friendly design, it stands as a solid choice in the realm of audio receivers. Whether for casual listening or a full cinematic experience, the RX-7520VBK promises to elevate any sound setup.