JVC RX-6012VSL manual English, Connecting the Power Cord, Putting Batteries in the Remote Control

Page 10
Digital connections

English

Digital connections

This receiver is equipped with two DIGITAL IN terminals — one digital coaxial terminal and one digital optical terminal.

You can connect any component to one of the digital terminals using a digital coaxial cable (not supplied) or digital optical cable (not supplied).

IMPORTANT:

When connecting the DVD player or digital TV broadcast tuner using the digital terminal, you also need to connect it to the video jack on the rear. Without connecting it to the video jack, you can view no playback picture.

After connecting the components using the DIGITAL IN terminals, set the following correctly if necessary.

Set the digital input (DIGITAL IN) terminal setting correctly. For details, see “Digital Input (DIGITAL IN) Terminal Setting” on page 14.

Select the digital input mode correctly. For details, see “Selecting the Analog or Digital Input Mode” on page 14.

Digital TV

DVD player

DVD

Connecting the Power Cord

Before plugging the receiver into an AC outlet, make sure that all connections have been made.

Plug the power cord into an AC outlet.

Keep the power cord away from the connecting cables and the antenna. The power cord may cause noise or screen interference. We recommend that you use a coaxial cable to connect the antenna, since it is well-shielded against interference.

Notes:

The preset settings such as preset channels and sound adjustment may be erased in a few days in the following cases:

–When you unplug the power cord. –When a power failure occurs.

If the wall outlet does not match the AC plug, use the supplied AC plug adaptor.

CAUTIONS:

Do not plug in before setting the voltage selector switch on the rear of the unit and all connection procedures are complete.

Do not touch the power cord with wet hands.

Do not pull on the power cord to unplug the cord. When unplugging the cord, always grasp the plug so as not to damage the cord.

Putting Batteries in the Remote Control

CD player

CD recorder

When the component has a digital coaxial output terminal, connect it to the DIGITAL 1 (DVD) terminal, using the digital coaxial cable (not supplied).

When the component has a digital optical output terminal, connect it to the DIGITAL 2 (CD) terminal, using the digital optical cable (not supplied).

Before using the remote control, put two supplied batteries first. When using the remote control, aim the remote control directly at the remote sensor on the receiver.

1

2

3

DIGITAL 1

 

 

(DVD)

 

 

 

1. On the back of the remote control, remove the

DIGITAL 2 ( CD )

battery cover.

Before connecting a digital

 

optical cable, unplug the

DIGITAL IN

protective plug.

 

Notes:

When shipped from the factory, the DIGITAL IN terminals have been set for use with the following components.

DIGITAL 1 (coaxial): For DVD player

DIGITAL 2 (optical): For CD player

When you want to operate the CD player or CD recorder using the COMPU LINK remote control system, connect the target component also as described in “Analog connections” (see page 5).

2.Insert batteries. Make sure to match the polarity:

(+) to (+) and (–) to (–).

3.Replace the cover.

If the range or effectiveness of the remote control decreases, replace the batteries. Use two R6P(SUM-3)/AA(15F) type dry-cell batteries.

CAUTION:

Follow these precautions to avoid leaking or cracking cells:

Place batteries in the remote control so they match the polarity: (+) to (+) and (–) to (–).

Use the correct type of batteries. Batteries that look similar may differ in voltage.

Always replace both batteries at the same time.

Do not expose batteries to heat or flame.

7

Image 10
Contents RX-6010VBK / RX-6012VSL MASTER VOLUMEVOLUME AUDIO/VIDEO CONTROL RECEIVERPrecaução --Interruptor Caution --switchPrecaución --Interruptor PRECAUCIÓNPrecaución Ventilación Adecuada English Español PortuguêsCaution Proper Ventilation Precaução ventilação apropriadaUsing the DSP Modes Table of ContentsBasic Settings COMPU LINK Remote Control SystemEnglish Parts IdentificationRemote Control q w e r t yChecking the Supplied Accessories Getting StartedBefore Installation Connecting the FM and AM AntennasConnecting the front speakers Connecting the SpeakersBasic connecting procedure Connecting the rear and center speakersPowered subwoofer Connecting Audio/Video ComponentsConnecting the subwoofer speaker EnglishDVD player EnglishVideo component connections To audioPlug the power cord into an AC outlet Connecting the Power CordPutting Batteries in the Remote Control EnglishTo turn on the power, press Basic OperationsTurning the Power On and Off Standby To turn off the power into standby modeFrom the remote control Listening Only with HeadphonesAdjusting the Volume To increase the volume, turn MASTERAttenuating the Input Signal Adjusting the Subwoofer Output LevelAdjusting the Tone EnglishAdjusting the Front Speaker Output Balance Basic SettingsSetting the Subwoofer Information English1. Press SETTING repeatedly until Setting the Speakers for the DSP ModesEnglish 1. Press SETTING repeatedly until EnglishEnglish Digital Input DIGITAL IN Terminal Setting1. Press SETTING repeatedly until Selecting the Analog or Digital Input ModeFrom the remote control ONLY Storing the Basic Settings and AdjustmentsUsing the Sleep Timer From the remote controlTuning in Stations Manually Receiving Radio BroadcastsSetting the AM Tuner Interval Spacing Using Preset TuningEnglish To tune in a preset stationFrom the remote control Selecting the FM Reception ModeWhat are the DSP Modes? Using the DSP ModesEnglish Surround modesDAP modes EnglishReproducing the Sound Field Available DSP modes according to the input modeBy pressing DSP MODE EnglishAvailable DSP modes By pressing SURROUND MODE5.Adjust the speaker output levels Adjusting the Surround ModesEnglish The PRO LOGIC and DSP indicators also JVC Theater Surround adjustmentsFrom the remote control EnglishEnglish Adjusting the DAP Modeson the display To cancel the DSP mode To cancel the Dolby/DTS Surround modeTo cancel the DSP mode To cancel the Dolby/DTS Surround modeAutomatic Source Selection COMPU LINK Remote Control SystemEnglish Synchronized RecordingOperating Audio Components Operating JVC’s Audio/Video ComponentsEnglish TunerCD changer EnglishOperating Video Components Cassette deckSOLUTION TroubleshootingPROBLEM EnglishAmplifier SpecificationsEnglish AudioAM tuner EnglishFM tuner IHF GeneralPRECAUÇÃO para a ligação à tensão da rede CA CAUTION for mains AC linePRECAUCIÓN para la línea de la red CA EN, SP, PR, CH