Troubleshooting
Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC service center.
PROBLEM | POSSIBLE CAUSE | SOLUTION |
| ||||
The display does not light up. | The power cord is not plugged in. | Plug the power cord into an AC outlet. |
| ||||
|
|
|
|
|
|
| |
No sound from speakers. | Speaker signal cables are not connected. | Check speaker wiring and reconnect if |
| ||||
|
| necessary. |
|
|
| ||
|
|
|
|
|
|
| |
| The SPEAKERS ON/OFF button is not | Press SPEAKERS ON/OFF button correctly. |
| ||||
| set correctly. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| An incorrect source is selected. | Select the correct source. |
|
|
| ||
|
|
|
| ||||
| Muting is activated. | Press MUTING to cancel the mute. |
| ||||
|
|
|
|
|
|
| |
| An incorrect input mode (analog or | Select the correct input mode (analog or |
| ||||
| digital) is selected. | digital). |
|
|
| ||
|
|
|
|
|
|
|
|
| Connections are incorrect. | Check connections. |
|
|
| ||
|
| For analog connections, see page 5. |
| ||||
|
| For digital connections, see page 7. |
| ||||
|
|
|
| ||||
Sound from one speaker only. | Speaker signal cables are not connected | Check speaker wiring and reconnect if |
| ||||
| properly. | necessary. |
|
|
| ||
|
|
|
| ||||
| The balance is set to one extreme. | Adjust the balance properly (see page 11). |
| ||||
|
|
|
| ||||
Continuous hiss or buzzing during FM | Incoming signal is too weak. | Connect an outdoor FM antenna or contact |
| ||||
reception. |
| your dealer. |
|
|
| ||
|
|
|
|
|
| ||
| The station is too far away. | Select a new station. |
|
|
| ||
|
|
|
| ||||
| An incorrect antenna is used. | Check with your dealer to be sure you have |
| ||||
|
| the correct antenna. |
|
|
| ||
|
|
|
|
|
| ||
| Antennas are not connected properly. | Check connections. |
|
|
| ||
|
|
|
| ||||
Occasional cracking noise during FM | Ignition noise from automobiles. | Move the antenna farther from automobile |
| ||||
reception. |
| traffic. |
|
|
| ||
|
|
|
|
|
|
|
|
“OVERLOAD” starts flashing on the | Speakers are overloaded because of high | 1. Press STANDBY/ON |
| on the front |
| ||
|
| ||||||
|
| ||||||
display. | volume. | panel to turn off the receiver. |
| ||||
|
| 2. Stop the playback source. |
| ||||
|
| 3. Turn on the receiver again, and adjust the |
| ||||
|
| volume. |
|
|
| ||
|
|
|
|
|
| ||
| Speakers are overloaded because of short | Press STANDBY/ON |
|
|
| on the front panel, |
|
|
|
|
|
| |||
|
|
|
| ||||
| circuit of speaker terminals. | then check the speaker wiring. |
| ||||
|
| If “OVERLOAD” does not disappear, unplug |
| ||||
|
| the AC power cord, then plug it back again. |
| ||||
|
| If speaker wiring is not |
| ||||
|
| your dealer. |
|
|
| ||
|
|
|
|
|
| ||
“DSP MICON NG” starts flashing on the | The | Press STANDBY/ON |
|
|
| on the front panel |
|
|
|
|
| ||||
|
|
| |||||
display. | functioning correctly. | to turn off the receiver. After unplugging the |
| ||||
|
| power cord, consult your dealer. |
| ||||
|
|
|
|
|
| ||
The STANDBY lamp lights up after | The receiver is overloaded because of a | Press STANDBY/ON |
|
|
| on the front panel |
|
|
|
|
| ||||
|
|
| |||||
turning on the power, but soon the | high voltage. | to turn off the receiver. After unplugging the |
| ||||
receiver turns off (into standby mode). |
| power cord, consult your dealer. |
| ||||
|
|
|
|
|
| ||
Remote control does not work. | There is an obstruction in front of the | Remove the obstruction. |
|
|
| ||
| remote sensor on the receiver. |
|
|
|
|
|
|
|
|
|
|
|
| ||
| Batteries are weak. | Replace batteries. |
|
|
| ||
|
|
|
| ||||
Remote control does not operate | An incorrect remote control operation | Select the correct remote control operation |
| ||||
intendedly. | mode is selected. | mode. (See page 26). |
|
|
| ||
|
|
|
|
|
|
|
|
English
28