JVC RX-6012VSL English, Storing the Basic Settings and Adjustments, Using the Sleep Timer, while

Page 18
In this case, press CONTROL UP 5/

English

When playing a software encoded with the DTS Digital

Surround, “AUTO” may not work properly and the following symptoms may occur:

Sound does not come out at the beginning of playback.

Noise comes out while using the searching or skipping function.

In this case, press CONTROL UP 5/

CONTROL

DOWN °to select “DTS” while “AUTO”

DOWN UP

 

is lit on the display.

Each time you press the button, the input mode changes as follows:

AUTO DOWN °to select “DTS” while “AUTO”is lit on the display. DTS

(Digital) (Digital)

The DIGITAL AUTO indicator does not light up on the display while “DTS” is selected.

To change the input mode back to “AUTO,” press CONTROL UP 5/DOWN ° while “DTS” is lit on the display after pressing

INPUT DIGITAL.

If AUTO  DTSStoring the Basic Settings and flashes while “DTS” is selected as the input mode, select “AUTO.”

Note:

When you turn off the power or select another source, “DTS” setting is canceled and the digital input mode is automatically reset to “AUTO.”

Storing the Basic Settings and

Adjustments

You can assign and store different sound settings for each different playing source. By using this function, you do not have to change the settings every time you change the source. The stored settings for the newly selected source are automatically recalled.

The following can be stored for each source:

Subwoofer output level (see page 10)

Input attenuator mode (see page 10)

Tone adjustment (see page 10)

Balance (see page 11)

DSP modes

Surround mode (see page 21)

DAP mode (see page 23)

The above settings are stored automatically in the following cases:

When you turn on the power.

When you change the source.

When you assign the source name.

Notes:

You cannot assign and store different settings for digital input mode and analog input mode.

If the source is FM or AM, you can assign a different setting for each band.

To change the input mode back to analog

 

input, press INPUT ANALOG.

INPUT ANALOG

“ANALOG” appears on the display for a

 

while.

INPUT ATT

 

Using the Sleep Timer

Using the Sleep Timer, you can fall asleep to music and know the receiver will turn off by itself rather than play all night.

From the remote control ONLY:

From the remote control:

1.Press the source selecting button (DVD, TV SOUND, CD, or TAPE/CDR)* for which you want to change the input mode.

Note:

DVD

TV SOUND

CD TAPE/CDR

Press SLEEP repeatedly.

SLEEP

 

The SLEEP indicator lights up on the display, and the shut-off time changes as follows

(in minutes):

To change the input mode back to analog10 input, press INPUT ANALOG. 20 “ANALOG” appears on the display for a30 while.40 Using the Sleep Timer50 10  20 30 40 50 60 70 80 9060 ANALOG  AUTO70 When the shut-off time comes80 To cancel the Sleep Timer90

00(Canceled) Manual background

*Among the sources listed above, you can select the digital input only for the sources which you have selected the digital input terminals for. (See “Digital Input (DIGITAL IN) Terminal Setting.”)

2. Press ANALOG/DIGITAL to

ANALOG/DIGITAL

 

change the input mode.

 

Each time you press the button, the input mode changes as follows:

ANALOG Manual backgroundManual background AUTO

(Digital)

When playing a software encoded with the DTS Digital

Surround, “AUTO” may not work properly. In this case, press CONTROL UP 5/DOWN ° on the front panel to select “DTS.” (See above.)

Note:

You can only select “ANALOG” and “AUTO” using the remote control.

When the shut-off time comes

The receiver turns off automatically.

To check or change the time remaining until the shut-off time

Press SLEEP once.

The remaining time until the shut-off time appears in minutes.

• To change the shut-off time, press SLEEP repeatedly.

To cancel the Sleep Timer

Press SLEEP repeatedly until “SLEEP 00 MIN.” appears on the display. (The SLEEP indicator goes off.)

• Turning off the power also cancels the Sleep Timer.

15

Image 18
Contents RX-6010VBK / RX-6012VSL MASTER VOLUMEVOLUME AUDIO/VIDEO CONTROL RECEIVERPrecaução --Interruptor Caution --switchPrecaución --Interruptor PRECAUCIÓNPrecaución Ventilación Adecuada English Español PortuguêsCaution Proper Ventilation Precaução ventilação apropriadaUsing the DSP Modes Table of ContentsBasic Settings COMPU LINK Remote Control SystemEnglish Parts IdentificationRemote Control q w e r t yChecking the Supplied Accessories Getting StartedBefore Installation Connecting the FM and AM AntennasConnecting the front speakers Connecting the SpeakersBasic connecting procedure Connecting the rear and center speakersPowered subwoofer Connecting Audio/Video ComponentsConnecting the subwoofer speaker EnglishDVD player EnglishVideo component connections To audioPlug the power cord into an AC outlet Connecting the Power CordPutting Batteries in the Remote Control EnglishTo turn on the power, press Basic OperationsTurning the Power On and Off Standby To turn off the power into standby modeFrom the remote control Listening Only with HeadphonesAdjusting the Volume To increase the volume, turn MASTERAttenuating the Input Signal Adjusting the Subwoofer Output LevelAdjusting the Tone EnglishAdjusting the Front Speaker Output Balance Basic SettingsSetting the Subwoofer Information EnglishSetting the Speakers for the DSP Modes 1. Press SETTING repeatedly untilEnglish 1. Press SETTING repeatedly until EnglishEnglish Digital Input DIGITAL IN Terminal Setting1. Press SETTING repeatedly until Selecting the Analog or Digital Input ModeFrom the remote control ONLY Storing the Basic Settings and AdjustmentsUsing the Sleep Timer From the remote controlTuning in Stations Manually Receiving Radio BroadcastsSetting the AM Tuner Interval Spacing Using Preset TuningEnglish To tune in a preset stationFrom the remote control Selecting the FM Reception ModeWhat are the DSP Modes? Using the DSP ModesEnglish Surround modesDAP modes EnglishReproducing the Sound Field Available DSP modes according to the input modeBy pressing DSP MODE EnglishAvailable DSP modes By pressing SURROUND MODEAdjusting the Surround Modes 5.Adjust the speaker output levelsEnglish The PRO LOGIC and DSP indicators also JVC Theater Surround adjustmentsFrom the remote control EnglishAdjusting the DAP Modes Englishon the display To cancel the DSP mode To cancel the Dolby/DTS Surround modeTo cancel the DSP mode To cancel the Dolby/DTS Surround modeAutomatic Source Selection COMPU LINK Remote Control SystemEnglish Synchronized RecordingOperating Audio Components Operating JVC’s Audio/Video ComponentsEnglish TunerCD changer EnglishOperating Video Components Cassette deckSOLUTION TroubleshootingPROBLEM EnglishAmplifier SpecificationsEnglish AudioAM tuner EnglishFM tuner IHF GeneralPRECAUÇÃO para a ligação à tensão da rede CA CAUTION for mains AC linePRECAUCIÓN para la línea de la red CA EN, SP, PR, CH