Basic Operations
The following operations are commonly used when you play any sound source.
English
Turning the Power On and Off (Standby)
| On the front panel: |
|
| ||
| To turn on the power, press | STANDBY | |||
STANDBY/ON |
|
|
| |
| . |
|
| |
|
|
| ||
|
|
| ||
The STANDBY lamp goes off. The name of | STANDBY/ON | |||
the current source (or station frequency) |
|
| ||
appears on the display. |
|
| ||
Selected source name appears
DIGITAL AUTO | SPK | INPUT ATT | SLEEP | |
ANALOG | L | C | R PROLOGIC DSP H.PHONE AUTOMUTING TUNED STEREO | VOLUME |
LINEAR PCM | S.WFR LFE |
| ||
DIGITAL | LS | S | RS |
|
CH-
Current source name appears
SPK
ANALOG | L | R | VOLUME |
Current volume level is shown here
DVD | Select the DVD player. |
TV SOUND | Select the TV sound. |
VCR | Select the video component connected to the |
| VCR jacks. |
CD * | Select the CD player. |
TAPE/CDR * | Select the cassette deck (or the CD recorder). |
FM/AM * | Select an FM or AM broadcast. |
| • Each time you press the button, the band |
press STANDBY/ON 
again.
The STANDBY lamp lights up. A small amount of power is consumed in standby mode. To turn the power off completely, unplug the AC power cord.
From the remote control:To turn on the power, press AUDIO in the
(standby/on) section.
The STANDBY lamp goes off. The name of the current source (or station frequency) appears on the display.
STANDBY
STANDBY/ON
AUDIO
alternates between FM and AM. |
Notes:
•When connecting a CD recorder (to the TAPE/CDR jacks), change the source name that appears on the display. See page 11 for details.
•When you have connected some digital source components using the digital terminals (see page 7), you need to select the digital input mode.
•When you press one of the source selecting buttons on the remote control marked above with an asterisk (*), the receiver automatically turns on.
To turn off the power (into standby mode),
press AUDIO in the 
(standby/on) section again.
The STANDBY lamp lights up.
Selecting the Source to PlayPress one of the source selecting buttons.The signal indicators light up in the following cases:
•Only the indicators for the incoming signals light up.
•When analog input is selected, “L” and “R” always light up.
The speaker indicators light up only•When the corresponding speaker is activated.
AND
•When the corresponding speaker is required for the DSP mode selected currently.
On the front panel:
DVD |
| VCR |
| TV SOUND |
CD |
| TAPE/CDR |
| FM/AM |
|
| |||
|
|
|
|
|
|
| SOURCE NAME |
|
|
Signal indicators light up in red:
L 
C 
R
S.WFR LFE
LS S RS
Speaker indicators light up in white:
L C R
S.WFR LFE
LS S RS
From the remote control:
DVD | TV SOUND | VCR |
CD | TAPE/CDR | FM/AM |
L: • When digital input is selected: Lights up when the left
channel signal comes in.
•When analog input is selected: Always lights up.R: • When digital input is selected: Lights up when the right
channel signal comes in.
•When analog input is selected: Always lights up.
C:Lights up when the center channel signal comes in. LS: Lights up when the left rear channel signal comes in. RS: Lights up when the right rear channel signal comes in.
S:Lights up when the monaural rear channel signal comes in. LFE: Lights up when the LFE channel signal comes in.
Note:
When “SUBWOOFER” is set to “YES” (see page 11), S.WFR lights up.
8