JVC RX-6012VSL manual English, Adjusting the Surround Modes, Adjust the speaker output levels

Page 24
Adjusting the Surround Modes
D I G I T A L
DOLBY SURROUND

English

Adjusting the Surround Modes

Once you have adjusted the Surround modes, the adjustment is memorized for each Surround mode.

Dolby and DTS Surround adjustments

Before you start, remember...

Make sure that you have set the speaker information correctly

(see page 12).

5.Adjust the speaker output levels.

To adjust the center speaker level, press CENTER +/– (from +10 dB to –10 dB).

To adjust the left rear speaker level, press REAR•L +/– (from +10 dB to –10 dB).

To adjust the right rear speaker level, press REAR•R +/– (from +10 dB to –10 dB).

– CENTER +

5 5.Adjust the speaker output levels.Manual backgroundManual backgroundManual backgroundManual background 6

– REAR•L +

8 Manual backgroundManual backgroundManual backgroundManual backgroundManual background 9

MENU

– REAR•R +

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 3 again.

• You cannot adjust the rear speaker output levels when you have set

“REAR SPK” to “NO.” See page 12.

• You cannot adjust the center speaker output level when you have

set “CENTER SPK” to “NO.” See page 12.

From the remote control:

1. Select and play a sound source.

6.Press TEST again to stop the test tone.

On the front panel:

10 Manual backgroundManual backgroundManual backgroundManual backgroundManual background +10

ENTER

TEST

1

• To enjoy Dolby Pro Logic, play back a software encoded with

Dolby Surround and labeled with Manual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual background mark.

• To enjoy Dolby Digital, play back a software encoded with

Dolby Digital and labeled with Manual background mark.

To enjoy DTS Digital Surround, play back a software encoded

with DTS Digital Surround and labeled with Manual background mark.

2. Press SURROUND to activate an

SURROUND

appropriate Surround mode —

 

PRO LOGIC, DOLBY DIGITAL

SURROUND

MODE

or DTS SURROUND.

 

When “PRO LOGIC” is selected,

the PRO LOGIC indicator lights up on the display.

Each time you press the button, the Surround mode turns on and off alternately.

Note:

You can also press SURROUND MODE to activate an appropriate Surround mode — PRO LOGIC, DOLBY DIGITAL, or DTS SURROUND.

3. Press SOUND.

SOUND

 

You can also use the buttons on the front panel to adjust the Surround modes. However, no test tone is available when using the buttons on the front panel. So, make adjustments while listening to the sound of the source played back.

1. Select and play a sound source.

• To enjoy Dolby Pro Logic, play back a software encoded with

Dolby Surround and labeled with Manual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual background DOLBY SURROUND mark.

• To enjoy Dolby Digital, play back a software encoded with

Dolby Digital and labeled with Manual background mark.

D I G I T A L

To enjoy DTS Digital Surround, play back a software encoded

with DTS Digital Surround and labeled with Manual background mark.

2. Press SURROUND ON/OFF to

SURROUND ON/OFF

 

activate an appropriate Surround

 

mode — PRO LOGIC, DOLBY

 

DIGITAL or DTS SURROUND.

 

When “PRO LOGIC” is selected, the PRO LOGIC indicator lights up on the display.

Each time you press the button, the Surround mode turns on and off alternately.

The 10 keys are activated for sound adjustments.

4. Press TEST to check the speaker

TEST

 

 

 

 

 

 

 

 

 

 

 

output balance.

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

 

 

“TEST TONE L” starts flashing on the

 

 

 

 

display, and a test tone comes out of the

 

 

 

 

speakers in the following order:

 

 

 

 

 

 

 

TEST TONE L

 

 

TEST TONE C

 

 

TEST TONE R

 

 

(Left front speaker)

(Center speaker)

(Right front speaker)

 

 

TEST TONE LS

TEST TONE RS

 

 

(Left rear speaker)

 

(Right rear speaker)

 

 

Notes:

You can adjust the speaker output levels without outputting the test tone.

No test tone comes out of the center speaker when “CENTER SPK” is set to “NO” (see page 12).

No test tone comes out of the rear speakers when “REAR SPK” is set to “NO” (see page 12).

3.Adjust the speaker output levels.

1)Press ADJUST repeatedly until one of the following indications appears on the display.

“CENTER LEVEL”:

To adjust the center speaker level. “REAR L LEVEL”:

To adjust the left rear speaker level. “REAR R LEVEL”:

To adjust the right rear speaker level.

2)Press CONTROL UP 5/DOWN °to adjust the selected speaker output level (from +10 dB to –10 dB).

3)Repeat 1) and 2) to adjust the other speaker output levels.

ADJUST SETTING

CONTROL

DOWN UP

21

Image 24
Contents MASTER VOLUME VOLUMERX-6010VBK / RX-6012VSL AUDIO/VIDEO CONTROL RECEIVERCaution --switch Precaución --InterruptorPrecaução --Interruptor PRECAUCIÓNEnglish Español Português Caution Proper VentilationPrecaución Ventilación Adecuada Precaução ventilação apropriadaTable of Contents Basic SettingsUsing the DSP Modes COMPU LINK Remote Control SystemParts Identification Remote ControlEnglish q w e r t yGetting Started Before InstallationChecking the Supplied Accessories Connecting the FM and AM AntennasConnecting the Speakers Basic connecting procedureConnecting the front speakers Connecting the rear and center speakersConnecting Audio/Video Components Connecting the subwoofer speakerPowered subwoofer EnglishEnglish Video component connectionsDVD player To audioConnecting the Power Cord Putting Batteries in the Remote ControlPlug the power cord into an AC outlet EnglishBasic Operations Turning the Power On and Off StandbyTo turn on the power, press To turn off the power into standby modeListening Only with Headphones Adjusting the VolumeFrom the remote control To increase the volume, turn MASTERAdjusting the Subwoofer Output Level Adjusting the ToneAttenuating the Input Signal EnglishBasic Settings Setting the Subwoofer InformationAdjusting the Front Speaker Output Balance EnglishSetting the Speakers for the DSP Modes 1. Press SETTING repeatedly untilEnglish 1. Press SETTING repeatedly until EnglishDigital Input DIGITAL IN Terminal Setting 1. Press SETTING repeatedly untilEnglish Selecting the Analog or Digital Input ModeStoring the Basic Settings and Adjustments Using the Sleep TimerFrom the remote control ONLY From the remote controlReceiving Radio Broadcasts Setting the AM Tuner Interval SpacingTuning in Stations Manually Using Preset TuningTo tune in a preset station From the remote controlEnglish Selecting the FM Reception ModeUsing the DSP Modes EnglishWhat are the DSP Modes? Surround modesEnglish Reproducing the Sound FieldDAP modes Available DSP modes according to the input modeEnglish Available DSP modesBy pressing DSP MODE By pressing SURROUND MODEAdjusting the Surround Modes 5.Adjust the speaker output levelsEnglish JVC Theater Surround adjustments From the remote controlThe PRO LOGIC and DSP indicators also EnglishAdjusting the DAP Modes Englishon the display To cancel the Dolby/DTS Surround mode To cancel the DSP modeTo cancel the DSP mode To cancel the Dolby/DTS Surround modeCOMPU LINK Remote Control System EnglishAutomatic Source Selection Synchronized RecordingOperating JVC’s Audio/Video Components EnglishOperating Audio Components TunerEnglish Operating Video ComponentsCD changer Cassette deckTroubleshooting PROBLEMSOLUTION EnglishSpecifications EnglishAmplifier AudioEnglish FM tuner IHFAM tuner GeneralCAUTION for mains AC line PRECAUCIÓN para la línea de la red CAPRECAUÇÃO para a ligação à tensão da rede CA EN, SP, PR, CH