JVC RX-6012RSL manual Basic Operations, Turning the Power On and Off Standby, On the front panel

Page 11

Basic Operations

The following operations are commonly used when you play any sound source.

Turning the Power On and Off (Standby)

On the front panel:

 

 

To turn on the power, press

STANDBY

STANDBY/ON

 

 

 

 

.

 

 

 

 

 

 

 

 

 

 

 

The STANDBY lamp goes off. The name of

STANDBY/ON

the current source (or station frequency)

 

 

appears on the display.

 

 

Selected source name appears

DIGITAL AUTO

SPK

INPUT ATT

EON RDS

SLEEP

ANALOG

L

C

R PROLOGIC DSP H.PHONE AUTOMUTING TUNED STEREO TA NEWS INFO VOLUME

LINEAR PCM

S.WFR LFE

 

 

DIGITAL

LS

S

RS

 

 

 

 

 

CH-

 

 

 

 

 

 

 

 

Current source name appears

SPK

ANALOG

L

R

VOLUME

Current volume level is shown here

DVD

Select the DVD player.

TV SOUND

Select the TV sound.

VCR

Select the video component connected to the

 

VCR jacks.

CD *

Select the CD player.

TAPE/CDR *

Select the cassette deck (or the CD recorder).

FM/AM *

Select an FM or AM (MW/LW) broadcast.

 

• Each time you press the button, the band

To turn off the power (into standby mode),

press STANDBY/ON again.

The STANDBY lamp lights up. A small amount of power is consumed in standby mode. To turn the power off completely, unplug the AC power cord.

From the remote control:

To turn on the power, press AUDIO in the

(standby/on) section.

The STANDBY lamp goes off. The name of the current source (or station frequency) appears on the display.

STANDBY

STANDBY/ON

AUDIO

alternates between FM and AM (MW/LW).

Notes:

•When connecting a CD recorder (to the TAPE/CDR jacks), change the source name that appears on the display. See page 11 for details.

•When you have connected some digital source components using the digital terminals (see page 7), you need to select the digital input mode.

•When you press one of the source selecting buttons on the remote control marked above with an asterisk (*), the receiver automatically turns on.

To turn off the power (into standby mode),

press AUDIO in the (standby/on) section again.

The STANDBY lamp lights up.

Selecting the Source to Play

Press one of the source selecting buttons.

Signal and speaker indicators on the display

The signal indicators light up in the following cases:

•Only the indicators for the incoming signals light up.

•When analog input is selected, “L” and “R” always light up.

The speaker indicators light up only —:

•When the corresponding speaker is activated.

AND

•When the corresponding speaker is required for the DSP mode selected currently.

On the front panel:

DVD

 

VCR

 

TV SOUND

CD

 

TAPE/CDR

 

FM/AM

 

 

 

 

 

 

 

 

 

SOURCE NAME

 

 

Signal indicators light up in red:

L C R

S.WFR LFE

LS S RS

Speaker indicators light up in white:

L C R

S.WFR LFE

LS S RS

From the remote control:

DVD

TV SOUND

VCR

CD

TAPE/CDR

FM/AM

L: • When digital input is selected: Lights up when the left

channel signal comes in.

•When analog input is selected: Always lights up.

R: • When digital input is selected: Lights up when the right

channel signal comes in.

•When analog input is selected: Always lights up.

C:Lights up when the center channel signal comes in. LS: Lights up when the left rear channel signal comes in. RS: Lights up when the right rear channel signal comes in.

S:Lights up when the monaural rear channel signal comes in. LFE: Lights up when the LFE channel signal comes in.

Note:

When “SUBWOOFER” is set to “YES” (see page 11), S.WFR lights up.

8

Page 10 Page 12
Image 11
Page 10 Page 12
Contents RX-6010RBK / RX-6012RSL If in Doubt Consult a Competent Electrician RX-6010RBK RX-6012RSL Table of Contents W e r t Remote Control Front PanelParts Identification Getting Started Before InstallationChecking the Supplied Accessories Connecting the FM and AM MW/LW AntennasConnecting the rear and center speakers Connecting the SpeakersBasic connecting procedure Connecting the front speakersAudio component connections Connecting Audio/Video ComponentsConnecting the subwoofer speaker Analog connectionsTo video input Video component connectionsDVD player OutputDigital connections Connecting the Power CordPutting Batteries in the Remote Control Plug the power cord into an AC outletBasic Operations Turning the Power On and Off StandbyFrom the remote control Signal and speaker indicators on the displayPress Muting to mute the sound Listening Only with HeadphonesThrough all speakers and headphones Connected Muting the SoundAttenuating the Input Signal Adjusting the Subwoofer Output LevelAdjusting the Tone Changing the Source Name Basic SettingsRecording a Source Setting the Subwoofer Information Adjusting the Front Speaker Output BalanceSetting the Speakers for the DSP Modes To select the low frequency effect Attenuator level Crossover FRQ Crossover Frequency appears on the displayLFE ATT Low Frequency Effect Attenuator appears on Display Selecting the Analog or Digital Input Mode Digital Input Digital in Terminal SettingPress Sleep repeatedly Storing the Basic Settings AdjustmentsUsing the Sleep Timer Change the input modeReceiving Radio Broadcasts Tuning in Stations ManuallyUsing Preset Tuning Selecting the FM Reception Mode Searching for a Program by PTY Codes Using the RDS Radio Data System to Receive FM StationsPress TA/NEWS/INFO until Switching to a Broadcast Program of Your Choice TemporarilyPress EON so that the last selected Program type appears on the displayTo stop listening to the program selected by EON You have selectedIf the FM station you are listening to is Surround modes Using the DSP ModesWhat are the DSP Modes? Possible × Impossible Reproducing the Sound FieldDAP modes Early reflections Behind Direct soundsFront Available DSP Modes According to the Speaker ArrangementAdjusting the Surround Modes Press Test again to stop the test tone Adjust the effect levelJVC Theater Surround adjustments Level you wantAdjust the rear speaker output Adjusting the DAP ModesPress DSP Mode repeatedly until Adjust the rear speaker output levels Press SoundPress Surround ON/OFF Mode you want appears on DisplayPress Surround Mode Activating the DSP ModesAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Press the play 3 button on the CD playerSound control section Amplifier Operating JVC’s Audio/Video ComponentsOperating Audio Components TunerCD recorder Operating Video ComponentsCD changer Cassette deckProblem Possible Cause Solution TroubleshootingAM MW/LW tuner SpecificationsAmplifier FM tuner IHF0301NHMMDWJEIN
Top Page Image Contents