JVC RX-6010RBK, RX-6012RSL manual RX-6010RBK RX-6012RSL

Page 3

SAFETY INSTRUCTIONS

“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”

This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured.

Do read the operating instructions before you attempt to use the equipment.

Do ensure that all electrical connections (including the mains plug, extension leads and interconnections between pieces of equipment) are properly made and in accordance with the manufacturer’s instructions. Switch off and withdraw the mains plug when making or changing connections.

Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.

Do be careful with glass panels or doors on equipment.

DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any way–switch off, withdraw the mains plug and consult your dealer.

DON’T remove any fixed cover as this may expose dangerous voltages.

DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or has a standby mode.

Switch off using the switch on the equipment and make sure that your family know how to do this.

Special arrangements may need to be made for infirm or handicapped people.

DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic safety. It is illegal to watch television whilst driving.

DON’T listen to headphones at high volume as such use can permanently damage your hearing.

DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings.

Overheating will cause damage and shorten the life of the equipment.

DON’T use makeshift stands and NEVER fix legs with wood screws — to ensure complete safety always fit the manufacturer’s approved stand or legs with the fixings provided according to the instructions.

DON’T allow electrical equipment to be exposed to rain or moisture.

ABOVE ALL

NEVER let anyone, especially children, push anything into holes, slots or any other opening in the case -this could result in a fatal electrical shock.;

NEVER guess or take chances with electrical equipment of any kind — it is better to be safe than sorry!

Caution: Proper Ventilation

To avoid risk of electric shock and fire and to protect from damage.

Locate the apparatus as follows:

Front:

No obstructions open spacing.

Sides:

No obstructions in 10 cm from the sides.

Top:

No obstructions in 10 cm from the top.

Back:

No obstructions in 15 cm from the back

Bottom:

No obstructions, place on the level surface.

In addition, maintain the best possible air circulation as illustrated.

Wall or obstructions

Spacing 15 cm or more

Front

RX-6010RBK/

RX-6012RSL

Stand height 15 cm or more

Floor

G-2

Image 3
Contents RX-6010RBK / RX-6012RSL If in Doubt Consult a Competent Electrician RX-6010RBK RX-6012RSL Table of Contents Remote Control Front Panel Parts IdentificationW e r t Getting Started Before InstallationChecking the Supplied Accessories Connecting the FM and AM MW/LW AntennasConnecting the rear and center speakers Connecting the SpeakersBasic connecting procedure Connecting the front speakersAudio component connections Connecting Audio/Video ComponentsConnecting the subwoofer speaker Analog connectionsTo video input Video component connectionsDVD player OutputDigital connections Connecting the Power CordPutting Batteries in the Remote Control Plug the power cord into an AC outletBasic Operations Turning the Power On and Off StandbyFrom the remote control Signal and speaker indicators on the displayPress Muting to mute the sound Listening Only with HeadphonesThrough all speakers and headphones Connected Muting the SoundAdjusting the Subwoofer Output Level Adjusting the ToneAttenuating the Input Signal Changing the Source Name Basic SettingsRecording a Source Setting the Subwoofer Information Adjusting the Front Speaker Output BalanceSetting the Speakers for the DSP Modes Crossover FRQ Crossover Frequency appears on the display LFE ATT Low Frequency Effect Attenuator appears on DisplayTo select the low frequency effect Attenuator level Selecting the Analog or Digital Input Mode Digital Input Digital in Terminal SettingPress Sleep repeatedly Storing the Basic Settings AdjustmentsUsing the Sleep Timer Change the input modeTuning in Stations Manually Using Preset TuningReceiving Radio Broadcasts Selecting the FM Reception Mode Searching for a Program by PTY Codes Using the RDS Radio Data System to Receive FM StationsPress TA/NEWS/INFO until Switching to a Broadcast Program of Your Choice TemporarilyPress EON so that the last selected Program type appears on the displayYou have selected If the FM station you are listening to isTo stop listening to the program selected by EON Using the DSP Modes What are the DSP Modes?Surround modes Possible × Impossible Reproducing the Sound FieldDAP modes Early reflections Behind Direct soundsFront Available DSP Modes According to the Speaker ArrangementAdjusting the Surround Modes Press Test again to stop the test tone Adjust the effect levelJVC Theater Surround adjustments Level you wantAdjust the rear speaker output Adjusting the DAP ModesPress DSP Mode repeatedly until Adjust the rear speaker output levels Press SoundPress Surround ON/OFF Mode you want appears on DisplayPress Surround Mode Activating the DSP ModesAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Press the play 3 button on the CD playerSound control section Amplifier Operating JVC’s Audio/Video ComponentsOperating Audio Components TunerCD recorder Operating Video ComponentsCD changer Cassette deckProblem Possible Cause Solution TroubleshootingAM MW/LW tuner SpecificationsAmplifier FM tuner IHF0301NHMMDWJEIN