JVC RX-6010RBK, RX-6012RSL manual Crossover FRQ Crossover Frequency appears on the display

Page 16

Crossover Frequency Setting

Small speakers cannot reproduce the bass sound very well. So, if you have used a small speaker for any of the front, center, and rear channels, this receiver automatically reallocates the bass elements, originally assigned to the channel for which you have connected the small speaker, to another channel (for which you have connected the large speaker).

If you have selected “LARGE” for all speakers (see page 12), this function will not take effect. To use this function properly, you need to set this crossover frequency level according to the size of the small speaker connected.

On the front panel ONLY:

1. Press SETTING repeatedly until

T SETTING

 

“CROSSOVER FRQ” (Crossover

 

 

 

 

 

 

Frequency) appears on the display.

The display changes to show the current setting.

2. Press CONTROL UP 5/DOWN ° CONTROL

DOWN UP

to select the crossover frequency level according to the size of the small speaker connected.

•Each time you press the button, the display changes to show the following:

Low Frequency Effect Attenuator Setting

If the bass sound is distorted while playing back a source using Dolby Digital or DTS Digital Surround, follow the procedure below.

On the front panel ONLY:

1. Press SETTING repeatedly until

ST SETTING

 

“LFE ATT” (Low Frequency

 

 

 

 

 

 

Effect Attenuator) appears on the

 

 

display.

 

 

The display changes to show the current setting.

 

 

2. Press CONTROL UP 5/DOWN °

CONTROL

DOWN UP

to select the low frequency effect

 

attenuator level.

 

•Each time you press the button, the display changes to show the following:

0dB 10dB

0dB: Normally select this.

10dB: Select this when the bass sound is distorted.

Note:

This function takes effect only when the subwoofer (LFE) signals come in, (with “SUBWOOFER” set to “YES.”)

80HZ 100HZ 120HZ

• Use the following comments as reference when adjusting.

80HZ:

Select this when the cone speaker unit built in the

 

speaker is about 4 3/4 inches (12 cm).

100HZ:

Select this when the cone speaker unit built in the

 

speaker is about 3 15/16 inches (10 cm).

120HZ:

Select this when the cone speaker unit built in the

 

speaker is about 3 3/16 inches (8 cm).

 

 

Note:

Crossover frequency is not valid for the HEADPHONE mode.

Dynamic Range Compression Setting

You can compress the dynamic range (difference between maximum sound and minimum sound) of the reproduced sound. This is useful when enjoying surround sound at night.

•This function takes effect only when playing back a source using Dolby Digital.

On the front panel ONLY:

1. Press SETTING repeatedly until

T SETTING

 

“D_RANGE COMP” (Dynamic

 

 

 

 

 

 

Range Compression) appears on the display.

The display changes to show the current setting.

2. Press CONTROL UP 5/DOWN ° CONTROL

DOWN UP

to select the appropriate item about the compression level.

•Each time you press the button, the display changes to show the following:

OFF MID MAX

OFF: Select this when you want to enjoy surround with its full dynamic range. (No effect applied.)

MID: Select this when you want to reduce the dynamic range a little. (Factory setting.)

MAX: Select this when you want to apply the compression effect fully. (Useful at night.)

Note:

Dynamic Range Compression is not valid for the DTS Digital

Surround.

13

Page 15 Page 17
Image 16
Page 15 Page 17
Contents RX-6010RBK / RX-6012RSL If in Doubt Consult a Competent Electrician RX-6010RBK RX-6012RSL Table of Contents Parts Identification Remote Control Front PanelW e r t Before Installation Checking the Supplied AccessoriesConnecting the FM and AM MW/LW Antennas Getting StartedConnecting the Speakers Basic connecting procedureConnecting the front speakers Connecting the rear and center speakersConnecting Audio/Video Components Connecting the subwoofer speakerAnalog connections Audio component connectionsVideo component connections DVD playerOutput To video inputConnecting the Power Cord Putting Batteries in the Remote ControlPlug the power cord into an AC outlet Digital connectionsTurning the Power On and Off Standby From the remote controlSignal and speaker indicators on the display Basic OperationsListening Only with Headphones Through all speakers and headphones ConnectedMuting the Sound Press Muting to mute the soundAdjusting the Tone Adjusting the Subwoofer Output LevelAttenuating the Input Signal Basic Settings Recording a Source Setting the Subwoofer InformationAdjusting the Front Speaker Output Balance Changing the Source NameSetting the Speakers for the DSP Modes LFE ATT Low Frequency Effect Attenuator appears on Display Crossover FRQ Crossover Frequency appears on the displayTo select the low frequency effect Attenuator level Digital Input Digital in Terminal Setting Selecting the Analog or Digital Input ModeStoring the Basic Settings Adjustments Using the Sleep TimerChange the input mode Press Sleep repeatedlyUsing Preset Tuning Tuning in Stations ManuallyReceiving Radio Broadcasts Selecting the FM Reception Mode Using the RDS Radio Data System to Receive FM Stations Searching for a Program by PTY CodesSwitching to a Broadcast Program of Your Choice Temporarily Press EON so that the last selectedProgram type appears on the display Press TA/NEWS/INFO untilIf the FM station you are listening to is You have selectedTo stop listening to the program selected by EON What are the DSP Modes? Using the DSP ModesSurround modes Reproducing the Sound Field DAP modesEarly reflections Behind Direct sounds Possible × ImpossibleAvailable DSP Modes According to the Speaker Arrangement FrontAdjusting the Surround Modes Adjust the effect level JVC Theater Surround adjustmentsLevel you want Press Test again to stop the test toneAdjusting the DAP Modes Press DSP Mode repeatedly untilAdjust the rear speaker output levels Press Sound Adjust the rear speaker outputMode you want appears on Display Press Surround ModeActivating the DSP Modes Press Surround ON/OFFCompu Link Remote Control System Remote Control through the Remote Sensor on the ReceiverPress the play 3 button on the CD player Automatic Source SelectionOperating JVC’s Audio/Video Components Operating Audio ComponentsTuner Sound control section AmplifierOperating Video Components CD changerCassette deck CD recorderTroubleshooting Problem Possible Cause SolutionSpecifications AmplifierFM tuner IHF AM MW/LW tuner0301NHMMDWJEIN
Top Page Image Contents