JVC RX-6012RSL manual Receiving Radio Broadcasts, Tuning in Stations Manually, Using Preset Tuning

Page 19

Receiving Radio Broadcasts

You can browse through all the stations or use the preset function to go immediately to a particular station.

Tuning in Stations Manually

On the front panel ONLY:

1. Press FM/AM to select the band

(FM or AM — MW/LW).	FM/AM

•Each time you press the button, the band alternates between FM and AM (MW/LW).

	SPK
ANALOG	L	R	TUNED	VOLUME

2. Press FM/AM TUNING 5/ °until FM/AM TUNING you find the frequency you want.

•Pressing FM/AM TUNING 5increases the frequency.

•Pressing FM/AM TUNING °decreases the frequency.

Notes:

•When you hold FM/AM TUNING 5/ ° in step 2, the frequency keeps changing until a station is tuned in.

•When a station of sufficient signal strength is tuned in, the TUNED indicator lights up on the display.

•When an FM stereo program is received, the STEREO indicator also lights up.

Using Preset Tuning

Once a station is assigned to a channel number, the station can be quickly tuned. You can preset up to 30 FM and 15 AM (MW/LW) stations.

2. Press MEMORY.		MEMORY
		MEMORY
SPK
ANALOG L R	TUNED	VOLUME

CH-

“CH-” appears and the channel number position starts flashing on the display for about 5 seconds.

3. Press FM/AM PRESET 5/ °to		FM/AM PRESET
		FM/AM PRESET
select a channel number while the
channel number position is
flashing.
SPK
ANALOG L R	TUNED	VOLUME

CH-

Note:

You can use the 10 keys on the remote control to select the preset number. When using the 10 keys, be sure that they are activated for the tuner, not for the CD and others. (See page 29.)

4. Press MEMORY again while the	MEMORY
selected channel number is flashing
on the display.

The selected channel number stops flashing.

The station is assigned to the selected channel number.

SPK

ANALOG

L

R

TUNED

VOLUME

CH-

To store the preset stations

Before you start, remember...

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

On the front panel ONLY:

1. Tune in the station you want to preset (see “Tuning in Stations Manually”).

If you want to store the FM reception mode for this station, select the FM reception mode you want. See “Selecting the FM Reception Mode” on page 17.

5.Repeat steps 1 to 4 until you store all the stations you want.

To erase a stored preset station

Storing a new station on a used number erases the previously stored one.

SPK

ANALOG

L

R

VOLUME

16

Image 19

Contents RX-6010RBK / RX-6012RSL If in Doubt Consult a Competent Electrician RX-6010RBK RX-6012RSL Table of Contents Parts Identification Remote Control Front PanelW e r t Getting Started Before InstallationChecking the Supplied Accessories Connecting the FM and AM MW/LW AntennasConnecting the rear and center speakers Connecting the SpeakersBasic connecting procedure Connecting the front speakersAudio component connections Connecting Audio/Video ComponentsConnecting the subwoofer speaker Analog connectionsTo video input Video component connectionsDVD player OutputDigital connections Connecting the Power CordPutting Batteries in the Remote Control Plug the power cord into an AC outletBasic Operations Turning the Power On and Off StandbyFrom the remote control Signal and speaker indicators on the displayPress Muting to mute the sound Listening Only with HeadphonesThrough all speakers and headphones Connected Muting the SoundAdjusting the Tone Adjusting the Subwoofer Output LevelAttenuating the Input Signal Changing the Source Name Basic SettingsRecording a Source Setting the Subwoofer Information Adjusting the Front Speaker Output BalanceSetting the Speakers for the DSP Modes LFE ATT Low Frequency Effect Attenuator appears on Display Crossover FRQ Crossover Frequency appears on the displayTo select the low frequency effect Attenuator level Selecting the Analog or Digital Input Mode Digital Input Digital in Terminal SettingPress Sleep repeatedly Storing the Basic Settings AdjustmentsUsing the Sleep Timer Change the input modeUsing Preset Tuning Tuning in Stations ManuallyReceiving Radio Broadcasts Selecting the FM Reception Mode Searching for a Program by PTY Codes Using the RDS Radio Data System to Receive FM StationsPress TA/NEWS/INFO until Switching to a Broadcast Program of Your Choice TemporarilyPress EON so that the last selected Program type appears on the displayIf the FM station you are listening to is You have selectedTo stop listening to the program selected by EON What are the DSP Modes? Using the DSP ModesSurround modes Possible × Impossible Reproducing the Sound FieldDAP modes Early reflections Behind Direct soundsFront Available DSP Modes According to the Speaker ArrangementAdjusting the Surround Modes Press Test again to stop the test tone Adjust the effect levelJVC Theater Surround adjustments Level you wantAdjust the rear speaker output Adjusting the DAP ModesPress DSP Mode repeatedly until Adjust the rear speaker output levels Press SoundPress Surround ON/OFF Mode you want appears on DisplayPress Surround Mode Activating the DSP ModesAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Press the play 3 button on the CD playerSound control section Amplifier Operating JVC’s Audio/Video ComponentsOperating Audio Components TunerCD recorder Operating Video ComponentsCD changer Cassette deckProblem Possible Cause Solution TroubleshootingAM MW/LW tuner SpecificationsAmplifier FM tuner IHF0301NHMMDWJEIN