JVC RX-6010RBK, RX-6012RSL manual Switching to a Broadcast Program of Your Choice Temporarily

Page 22

From the remote control:

1. Press PTY SEARCH while

1

1

 

 

£ PTY SEARCH

listening to an FM station.

 

 

“PTY SELECT” flashes on the display.

 

 

 

PTY

7 D I S P L AY + PTY

Switching to a Broadcast Program of Your Choice Temporarily

Another convenient RDS service is called “EON (Enhanced Other Network).”

2. Press and hold PTY +

 

or PTY – until the PTY

1

code you want appears

 

on the display, while

 

“PTY SELECT” is

PTY

 

flashing.

 

The display gives you the PTY codes described below.

3.Press PTY SEARCH again, while the PTY code selected in the previous step is still on the display.

£PTY SEARCH

 

1

7 D I S P L AY

+ PTY

£PTY SEARCH

1

1

PTY

7 DISPLAY + PTY

The EON indicator lights up while receiving an FM station with the EON code. (The EON indicator also lights up while receiving an AM station but the EON function will not work.)

This allows the receiver to switch temporarily to a broadcast program of your choice (NEWS, TA, and/or INFO) from a different station except in the following cases:

When you are listening to non-RDS stations (all AM — MW/LW and some FM stations).

When the last received FM station is a non-RDS station.

When the receiver is in standby mode.

Before you start, remember...

• The EON function is only applicable to preset stations.

While searching, “SEARCH” and the selected PTY code alternate on the display.

The receiver searches 30 preset FM stations, stops when it finds the one you have selected, and tunes in that station.

To continue searching after the first stop

Press PTY SEARCH again while the indications on the display are flashing.

If no program is found, “NOTFOUND” appears on the display.

PTY codes

NONE

ALARMNEWS

TEST

AFFAIRS

 

 

 

 

DOCUMENT

INFO (INFORMATION)

 

 

 

 

FOLK M (MUSIC)

SPORT

 

 

 

 

OLDIES

EDUCATE (EDUCATION)

 

 

 

 

 

 

NATION M (NATIONAL MUSIC)

DRAMA

 

 

 

 

 

 

COUNTRY

CULTURE

 

 

 

 

JAZZ

SCIENCE

 

 

 

 

 

 

LEISURE

VARIED

 

 

TRAVEL

 

POP M (MUSIC)

 

 

 

 

 

 

 

 

 

 

PHONE IN

 

ROCK M (MUSIC)

 

 

 

 

 

RELIGION

 

EASY M (MUSIC)

 

 

 

 

 

 

 

 

 

 

SOCIAL (AFFAIRS)

LIGHT M (MUSIC)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CLASSICS

CHILDREN

 

 

 

 

 

 

FINANCE

 

OTHER M (MUSIC)

 

 

WEATHER

On the front panel ONLY:

1. Press EON so that the last selected

EON

 

program type appears on the display.

The receiver enters EON standby mode. When the receiver is in EON standby mode, the receiver is ready to receive the EON data (TA/NEWS/INFO) you select.

2. Press TA/NEWS/INFO until the

TA/NEWS/INFO

 

program type you want appears on

 

the display.

 

Each time you press the button, the display changes to show the following:

TA NEWS INFO TA/NEWS

TA/NEWS/INFO NEWS/INFO TA/INFO

TA:

Traffic Announcement in your area.

NEWS: News.

INFO: Program the purpose of which is to impart advice in the widest sense.

19

Image 22
Contents RX-6010RBK / RX-6012RSL If in Doubt Consult a Competent Electrician RX-6010RBK RX-6012RSL Table of Contents Parts Identification Remote Control Front PanelW e r t Connecting the FM and AM MW/LW Antennas Before InstallationChecking the Supplied Accessories Getting StartedConnecting the front speakers Connecting the SpeakersBasic connecting procedure Connecting the rear and center speakersAnalog connections Connecting Audio/Video ComponentsConnecting the subwoofer speaker Audio component connectionsOutput Video component connectionsDVD player To video inputPlug the power cord into an AC outlet Connecting the Power CordPutting Batteries in the Remote Control Digital connectionsSignal and speaker indicators on the display Turning the Power On and Off StandbyFrom the remote control Basic OperationsMuting the Sound Listening Only with HeadphonesThrough all speakers and headphones Connected Press Muting to mute the soundAdjusting the Tone Adjusting the Subwoofer Output LevelAttenuating the Input Signal Adjusting the Front Speaker Output Balance Basic SettingsRecording a Source Setting the Subwoofer Information Changing the Source NameSetting the Speakers for the DSP Modes LFE ATT Low Frequency Effect Attenuator appears on Display Crossover FRQ Crossover Frequency appears on the displayTo select the low frequency effect Attenuator level Digital Input Digital in Terminal Setting Selecting the Analog or Digital Input ModeChange the input mode Storing the Basic Settings AdjustmentsUsing the Sleep Timer Press Sleep repeatedlyUsing Preset Tuning Tuning in Stations ManuallyReceiving Radio Broadcasts Selecting the FM Reception Mode Using the RDS Radio Data System to Receive FM Stations Searching for a Program by PTY CodesProgram type appears on the display Switching to a Broadcast Program of Your Choice TemporarilyPress EON so that the last selected Press TA/NEWS/INFO untilIf the FM station you are listening to is You have selectedTo stop listening to the program selected by EON What are the DSP Modes? Using the DSP ModesSurround modes Early reflections Behind Direct sounds Reproducing the Sound FieldDAP modes Possible × ImpossibleAvailable DSP Modes According to the Speaker Arrangement FrontAdjusting the Surround Modes Level you want Adjust the effect levelJVC Theater Surround adjustments Press Test again to stop the test toneAdjust the rear speaker output levels Press Sound Adjusting the DAP ModesPress DSP Mode repeatedly until Adjust the rear speaker outputActivating the DSP Modes Mode you want appears on DisplayPress Surround Mode Press Surround ON/OFFPress the play 3 button on the CD player Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Automatic Source SelectionTuner Operating JVC’s Audio/Video ComponentsOperating Audio Components Sound control section AmplifierCassette deck Operating Video ComponentsCD changer CD recorderTroubleshooting Problem Possible Cause SolutionFM tuner IHF SpecificationsAmplifier AM MW/LW tuner0301NHMMDWJEIN