Weider WBTL13608.0 user manual Assembly

Page 6

ASSEMBLY

To hire an authorized service technician to assemble the treadmill, call 1-800-445-2480.

Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill perfor- mance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires the included allen wrench and your own phillips screwdriver . For help identifying assembly hardware, see the drawings below. Note: If a part is not found in the part bags, check to see if the part has been preattached. To avoid damaging plastic parts, do not use power tools for assembly.

Nut (38)–2

Base Pad Spacer

Washer (78)–10

Star Washer

(71)–10

 

(77)–4

 

 

3/4” Screw (4)–2

1” Tek Screw (82)–4

 

Upright Bolt (72)–10

 

Wheel Bolt (85)–2

 

 

1.Identify the Right Upright (74), which has holes in the in- dicated locations.

Set the Right Upright (74) near the Frame (48) as shown. Insert the Upright Wire Harness (75) into the lower end of the Right Upright and out of the top. Place an elastic band around the Upright Wire Harness (75) and the Right Upright (74) to keep the Upright Wire Harness from falling into the Right Upright. Leave the elastic band on until step 8 is completed.

1

 

 

 

 

 

 

 

 

 

 

Large

48

 

75

74

Small

Hole

Band

 

Holes

 

 

 

 

 

 

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT QUESTIONS?Model No. WBTL13608.0 Serial No On the WEBTable of Contents Trends in general Important PrecautionsSpeed, accelerate, or stop unexpectedly Never leave the treadmill unattended while itPage Back Before YOU BeginFront Right SideAssembly Tighten the Upright Bolts yet Lower the Uprights to the floor see the inset drawingSee the two small inset drawings. Using your fingernail Careful to avoid losing the Shock PinPage Make sure that no wires are pinched. Reattach Ceiver so the small cylinder is oriented as shownHOW to Plug in the Power Cord Treadmill OperationPRE-LUBRICATED Walking Belt Features of the Console HOW to Turn on the PowerInsert the key into the console HOW to USE the Manual ModeSelect the manual mode Set a workout goal if desiredPage Measure your heart rate if desired Avoid moving your hands. WhenHOW to USE a Preset Program Adjust the program settings if desiredPress the Start button to start the program Follow your progress with the matrix and the displays Select one of the custom programs HOW to USE a Custom Program HOW to USE a Heart Rate Program Select a heart rate programFollow your progress with the matrix and the displays Information MODE/DEMO Mode Optional Chest Pulse SensorHOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useUnplug the Power CORD. If the walking Gap between the Magnet and the Reed Switch isProblem The walking belt slows when walked on Key and Unplug the Power CORD. UsingWorkout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencySuggested Stretches Page Part LIST-Model No. WBTL13608.0 Key No. Qty DescriptionQty Description DRAWING-Model No. WBTL13608.0 Exploded DRAWING-Model No Ordering Replacement Parts Limited WarrantyIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents