Weider WBTL13608.0 user manual Gap between the Magnet and the Reed Switch is, Top

Page 26
3–4”
Rear Roller Bolts

Next, locate the Reed Switch (14) and the Magnet (12) on

 

 

the left side of the Pulley (11). Turn the Pulley until the

13

1/8”

Magnet is aligned with the Reed Switch. Make sure that

the gap between the Magnet and the Reed Switch is

14

11

about 1/8”. If necessary, loosen the indicated 1/2” Screw

(13), move the Reed Switch slightly, and then retighten the

Top

12

Screw. Reattach the hood and run the treadmill for a few

 

minutes to check for a correct speed reading.

View

 

PROBLEM: The walking belt slows when walked on

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 11.

b. If the walking belt is overtightened, treadmill perfor- b mance may decrease and the walking belt may be permanently damaged. Remove the key and UN-

PLUG THE POWER CORD. Using the included allen wrench, turn both rear roller adjustment bolts counter- clockwise 1/4 of a turn. When the walking belt is prop- erly tightened, you should be able to lift each edge of the walking belt 3 to 4 inches off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

c.If the walking belt still slows when walked on, please see the front cover of this manual.

PROBLEM: The walking belt is off-center or slips when walked on

SOLUTION: a. If the walking belt is off-center, first remove the key

a

and UNPLUG THE POWER CORD. If the walking

belt has shifted to the left, use the allen wrench to

 

turn the left rear roller bolt clockwise 1/2 of a turn; if

 

the walking belt has shifted to the right, turn the

 

bolt counterclockwise 1/2 of a turn. Be careful not to

 

overtighten the walking belt. Then, plug in the power

 

cord, insert the key, and run the treadmill for a few

 

minutes. Repeat until the walking belt is centered.

 

b. If the walking belt slips when walked on, first remove

b

the key and UNPLUG THE POWER CORD. Using

the allen wrench, turn both rear roller bolts clockwise

 

1/4 of a turn. When the walking belt is correctly tight-

 

ened, you should be able to lift each edge of the

 

walking belt 3 to 4 inches off the walking platform. Be

 

careful to keep the walking belt centered. Then, plug

 

in the power cord, insert the key, and walk on the

 

treadmill for a few minutes. Repeat until the walking

 

belt is properly tightened.

 

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT QUESTIONS?Model No. WBTL13608.0 Serial No On the WEBTable of Contents Trends in general Important PrecautionsSpeed, accelerate, or stop unexpectedly Never leave the treadmill unattended while itPage Back Before YOU BeginFront Right SideAssembly Tighten the Upright Bolts yet Lower the Uprights to the floor see the inset drawingSee the two small inset drawings. Using your fingernail Careful to avoid losing the Shock PinPage Make sure that no wires are pinched. Reattach Ceiver so the small cylinder is oriented as shownPRE-LUBRICATED Walking Belt HOW to Plug in the Power CordTreadmill Operation Features of the Console HOW to Turn on the PowerInsert the key into the console HOW to USE the Manual ModeSelect the manual mode Set a workout goal if desiredPage Measure your heart rate if desired Avoid moving your hands. WhenPress the Start button to start the program HOW to USE a Preset ProgramAdjust the program settings if desired Follow your progress with the matrix and the displays Select one of the custom programs HOW to USE a Custom Program HOW to USE a Heart Rate Program Select a heart rate programFollow your progress with the matrix and the displays Information MODE/DEMO Mode Optional Chest Pulse SensorHOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useUnplug the Power CORD. If the walking Gap between the Magnet and the Reed Switch isProblem The walking belt slows when walked on Key and Unplug the Power CORD. UsingWorkout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencySuggested Stretches Page Part LIST-Model No. WBTL13608.0 Key No. Qty DescriptionQty Description DRAWING-Model No. WBTL13608.0 Exploded DRAWING-Model No Icon Health & Fitness, Inc., 1500 S W., Logan, UT Ordering Replacement PartsLimited Warranty
Top Page Image Contents