Weider WBTL13608.0 user manual

Page 9

8.Remove the elastic band holding the Upright Wire Harness (75). Have two people hold the console assem- bly near the Left Upright (73) and the Right Upright (74). Connect the Upright Wire Harness to the console wire.

Make sure to connect the connectors properly (see the inset drawing); the connectors should slide to- gether easily and snap into place. If the connectors do not slide together easily and snap into place, turn one connector and try again to connect them. IF THE CON-

NECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON.

Insert the Upright Wire Harness (75) and the console wire into the Right Upright (74). Next, insert the front ends of the brackets on the console assembly into the Right Upright and the Left Upright (73). Be careful not to pinch the wires.

9.While pressing down on the Handrails (99), attach the console assembly to the Uprights (73, 74) with four Upright Bolts (72), four Washers (78), and four Star Washers (71). Start all four Upright Bolts before tight- ening them.

Note: The Left Accessory Tray (63) and the Right Accessory Tray (64) are replaceable. If these parts be- come dislodged from the console assembly, simply press them back in.

10.Remove the knob from the pin. Make sure that the collar and the spring are on the pin. (Note: If there are two col- lars, place one on each side of the spring.) Next, insert the pin into the hole in the side of the Handrail (99). Then, tighten the knob back onto the pin.

8

 

 

 

 

 

 

 

 

Console

73

 

 

 

Assembly

 

 

Front of Bracket

 

 

 

Console Wire

 

 

 

75

 

 

 

 

74

 

 

 

 

 

75

9Console

63

 

 

64

Assembly

 

 

 

99

 

72

 

 

73

71

78

 

78

71

74

 

 

 

 

 

99

 

 

10

Knob

 

 

 

 

 

99

 

 

 

Pin

 

 

Spring

 

 

 

Collar

 

 

9

Image 9
Contents Model No. WBTL13608.0 Serial No QUESTIONS?Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT On the WEBTable of Contents Speed, accelerate, or stop unexpectedly Important PrecautionsTrends in general Never leave the treadmill unattended while itPage Front Before YOU BeginBack Right SideAssembly Lower the Uprights to the floor see the inset drawing Tighten the Upright Bolts yetCareful to avoid losing the Shock Pin See the two small inset drawings. Using your fingernailPage Ceiver so the small cylinder is oriented as shown Make sure that no wires are pinched. ReattachHOW to Plug in the Power Cord Treadmill OperationPRE-LUBRICATED Walking Belt HOW to Turn on the Power Features of the ConsoleSelect the manual mode HOW to USE the Manual ModeInsert the key into the console Set a workout goal if desiredPage Avoid moving your hands. When Measure your heart rate if desiredHOW to USE a Preset Program Adjust the program settings if desiredPress the Start button to start the program Follow your progress with the matrix and the displays Select one of the custom programs HOW to USE a Custom Program Select a heart rate program HOW to USE a Heart Rate ProgramFollow your progress with the matrix and the displays Optional Chest Pulse Sensor Information MODE/DEMO ModeHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingProblem The walking belt slows when walked on Gap between the Magnet and the Reed Switch isUnplug the Power CORD. If the walking Key and Unplug the Power CORD. UsingExercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Page Key No. Qty Description Part LIST-Model No. WBTL13608.0Qty Description DRAWING-Model No. WBTL13608.0 Exploded DRAWING-Model No Ordering Replacement Parts Limited WarrantyIcon Health & Fitness, Inc., 1500 S W., Logan, UT