Weider WBTL13608.0 user manual Troubleshooting, Problem The power turns off during use

Page 25

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual. PROBLEM: The power does not turn on

	SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
	is plugged into a properly grounded outlet (see page 11). Use only a single-outlet surge suppres-
	sor that meets all of the specifications described on page 11. Important: The treadmill is not com-
	patible with GFCI-equipped outlets.
	b. Make sure that the key is inserted into the console.
	c. Check the reset/off circuit breaker located on the frame near the	c
	power cord. If the switch protrudes as shown, the circuit breaker has	c
	tripped. To reset the circuit breaker, wait for five minutes and then
	press the switch back in.	Off	Reset
	PROBLEM: The power turns off during use	Off	Reset
	PROBLEM: The power turns off during use

SOLUTION: a. Check the reset/off circuit breaker (see drawing c above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console and then reinsert it.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Remove the key from the console and UNPLUG THE POWER CORD. Place the treadmill in the storage position (see HOW TO FOLD AND MOVE THE TREADMILL on page 23).

Next, remove the two indicated 3/4” Screws (4). 4

4

Lower the treadmill (see HOW TO LOWER THE TREAD-	4	4
MILL FOR USE on page 24). Remove the four indicated	4	4
3/4” Screws (4), and remove the Hood (44).
	44

25

Image 25

Contents Model No. WBTL13608.0 Serial No QUESTIONS?Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT On the WEBTable of Contents Speed, accelerate, or stop unexpectedly Important PrecautionsTrends in general Never leave the treadmill unattended while itPage Front Before YOU BeginBack Right SideAssembly Lower the Uprights to the floor see the inset drawing Tighten the Upright Bolts yetCareful to avoid losing the Shock Pin See the two small inset drawings. Using your fingernailPage Ceiver so the small cylinder is oriented as shown Make sure that no wires are pinched. ReattachTreadmill Operation HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt HOW to Turn on the Power Features of the ConsoleSelect the manual mode HOW to USE the Manual ModeInsert the key into the console Set a workout goal if desiredPage Avoid moving your hands. When Measure your heart rate if desiredAdjust the program settings if desired HOW to USE a Preset ProgramPress the Start button to start the program Follow your progress with the matrix and the displays Select one of the custom programs HOW to USE a Custom Program Select a heart rate program HOW to USE a Heart Rate ProgramFollow your progress with the matrix and the displays Optional Chest Pulse Sensor Information MODE/DEMO ModeHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingProblem The walking belt slows when walked on Gap between the Magnet and the Reed Switch isUnplug the Power CORD. If the walking Key and Unplug the Power CORD. UsingExercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Page Key No. Qty Description Part LIST-Model No. WBTL13608.0Qty Description DRAWING-Model No. WBTL13608.0 Exploded DRAWING-Model No Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT