Weider 740 user manual Spacer, 8 x 1 Bolt 59, a 3/8 Plain Nut 56 and a 3/8, 15b

Page 11

15.Refer to drawing 15a. Remove the 5/16” x 6” Bolt (7), the two 1/2” x 1” Spacers (51), the 1/2” x 1 3/8” Spacer (61), and the 5/16” Nylon Locknut (3) from the Weight Guides (62) and the Top Frame (55).

Refer to drawing 15b. Route the Short Cable (58) up through the indicated slot in the Top Frame (55). Wrap the Short Cable around a 3 1/2” Pulley (15) in the direction shown and slide the Pulley into the slot in

the Top Frame from the back. Attach the Pulley inside

the slot with a 3/8” x 2” Bolt (12), two 1/2” x 1/4” Spacers (44), two 3/8” Flat Washers (9), and a 3/8” Nylon Jamnut (22).

Refer to drawing 15a. Re-attach the 5/16” x 6” Bolt

(7), the two 1/2” x 1” Spacers (51), the 1/2” x 1 3/8”

Spacer (61), and the 5/16” Nylon Locknut (3). Make sure that the Short Cable is between the Pulley

and the Spacer.

Refer to drawing 15b. Press a 1 1/2” Square Inner

Cap (32) into the indicated end of the Top Frame (55).

16.Attach the loop at the end of the Short Cable (58) to

the Weight Tube (63) with a 5/16” x 1 1/2” Bolt (11) and a 5/16” Nylon Locknut (3).

17.Locate the Butterfly Cable (76). It is approximately 87 1/2“ long and it has a closed loop on both ends.

Attach one end of the Butterfly Cable (76) to the welded bracket on the back of the Right Arm (48) with

a 3/8” x 1” Bolt (59), a 3/8” Plain Nut (56) and a 3/8”

Nylon Jamnut (22). Note: Make sure the Plain Nut and the Jamnut are mounted in the order shown here. Do not overtighten the Nylon Locknut; it must be possible to pivot the Cable.

18.Wrap the Butterfly Cable (76) around a Large Pulley

(39)in the direction shown.

Attach the Large Pulley (39) and a Long Cable Trap

(50) to the welded bracket on the right side of the

Upright (42) with a 3/8” x 2 1/2” Bolt (60) and a 3/8”

Nylon Locknut (21). Note: Make sure the Cable Trap is oriented as shown.

15a

 

15b

 

44

 

61

 

 

 

 

15

 

 

3

 

 

 

 

 

 

 

51

 

44

22

7

 

 

 

9

 

 

 

 

 

55

 

 

 

 

32

 

 

 

62

 

9

55

 

 

12

 

58

16

3

 

58

 

 

 

 

 

 

63

 

 

 

 

 

 

 

11

17

 

 

59

 

 

Welded Bracket

 

 

 

 

 

 

 

76

56

 

 

 

 

 

 

 

 

22

48

 

 

 

 

 

18

 

 

 

 

 

Welded Bracket

 

21

 

 

50

 

 

 

 

60

39

 

 

 

 

 

 

 

 

 

42

 

 

 

76

 

 

11

Image 11
Contents Serial Number Decal Model No. WESY74091 Serial NoLimited Warranty Table of ContentsKeep hands and feet away from moving parts Important PrecautionsMake sure the cables remain on the pulleys Before You Begin Using the weight systemTo complete the process over a couple of evenings AssemblyTo make the assembly process as smooth as possi Tighten the Nylon Locknuts yet Locate and open the parts bag labeled Frame AssemblySee the inset drawing Bolts with two 5/16 Nylon LocknutsFrame Place the Top Frame 55 on top of the UprightDo not tighten Nylon Locknuts3 yet SlotMake sure the welded tab on the Press Frame Top Frame Weight Guide TubeTop Frame Locate and open the parts bag labeled ARMTion of the welded bracket a on each Arm Cable Trap is oriented as shown Locate the parts bag labeled Cable AssemblyShort Cable 58 is between the Pulley 15 Bolt 12 and a 3/8 Nylon Locknut15b Spacer8 x 1 Bolt 59, a 3/8 Plain Nut 56 and a 3/8 From Pulley To Pulley Bracket Onto the Bolt to prevent the Pulley from falling off durIng the following steps. Note Make sure the Pulley View from behindSpacer Bolt 12 and a 3/8 Nylon Locknut 21. NoteMake sure the Cable Trap is oriented as shown To the Seat 13 with two 1/4 x 3/4 Screws Shooting and Maintenance on Cable Diagrams58, 126 1/4 Long Cable76, 87 1/2 Attaching the Lat Bar to the Pulley Station AdjustmentCise will be reduced Changing the Weight Setting Adjusting the Arms for Butterfly or Press ExercisesCable and re-install it Trouble-shooting and MaintenanceTop Weight Resistance ChartStation Lever Part No R0101A Ordering Replacement PartsWESY74091 R0101A Remove this Part Identification Chart from the ManualPart Identification Chart-WESY74091 Page Page Remove this Part LIST/EXPLODED Drawing from the Manual 16 x 2 1/4 Bolt Backrest Nylon Locknut Part List-Model No. WESY74091Qty Description Exploded Drawing-Model No. WESY74091 R0101A