Weider 740 user manual Trouble-shooting and Maintenance, Cable and re-install it

Page 18

Trouble-shooting and Maintenance

Inspect and tighten all parts each time you use the weight system. Replace any worn parts immediately. The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use sol- vents.

Tightening the Cables

 

Woven cable, the type of cable used on the home gym

 

system, can stretch slightly when it is first used. If there

 

is slack in the Cables before resistance is felt, the

 

Cables should be tightened.

 

To tighten the Cables, insert the Weight Pin (26, not

 

shown) between the third and the fourth Weight, count-

29

ing from the top. See “Changing the Weight Setting” on

35

page 17 for instructions on moving the Weight Pin.

 

Tighten the 3/8” Plain Nut (56) a few turns further onto

22

the 3/8” Eyebolt (35) and then tighten the 3/8” Nylon

 

Jamnut (22) securing the Eyebolt to the Leg Lever (29).

56

Repeat this procedure until the Cables feel tighter.

 

Additional slack can be removed by moving the upper

3 1/2” Pulley (15) attached to the “I”-Plates (20) to the lower hole. To do this, remove the 3/8” x 2” Bolt (12),

Cable Trap (66) and 3/8” Nylon Locknut (21). Move the Pulley and re-attach it with the Bolt, Cable Trap and Locknut. Make sure the Cable Trap is oriented as shown.

Note: If a Cable tends to slip off the Pulleys often, the Cable may have become twisted. Remove the

Cable and re-install it.

If the Cables need to be replaced, see ORDERING REPLACEMENT PARTS on the back cover of this manual.

66

21

15

20

12

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model No. WESY74091 Serial No Serial Number DecalTable of Contents Limited WarrantyImportant Precautions Make sure the cables remain on the pulleysKeep hands and feet away from moving parts Using the weight system Before You BeginAssembly To make the assembly process as smooth as possiTo complete the process over a couple of evenings Bolts with two 5/16 Nylon Locknuts Locate and open the parts bag labeled Frame AssemblySee the inset drawing Tighten the Nylon Locknuts yetSlot Place the Top Frame 55 on top of the UprightDo not tighten Nylon Locknuts3 yet FrameLocate and open the parts bag labeled ARM Top Frame Weight Guide TubeTop Frame Make sure the welded tab on the Press FrameTion of the welded bracket a on each Arm Bolt 12 and a 3/8 Nylon Locknut Locate the parts bag labeled Cable AssemblyShort Cable 58 is between the Pulley 15 Cable Trap is oriented as shownSpacer 8 x 1 Bolt 59, a 3/8 Plain Nut 56 and a 3/815b View from behind Onto the Bolt to prevent the Pulley from falling off durIng the following steps. Note Make sure the Pulley From Pulley To Pulley BracketBolt 12 and a 3/8 Nylon Locknut 21. Note Make sure the Cable Trap is oriented as shownSpacer To the Seat 13 with two 1/4 x 3/4 Screws Cable Diagrams Shooting and Maintenance onLong Cable 76, 87 1/258, 126 1/4 Adjusting the Arms for Butterfly or Press Exercises AdjustmentCise will be reduced Changing the Weight Setting Attaching the Lat Bar to the Pulley StationTrouble-shooting and Maintenance Cable and re-install itWeight Resistance Chart Station LeverTop Ordering Replacement Parts Part No R0101ARemove this Part Identification Chart from the Manual WESY74091 R0101APart Identification Chart-WESY74091 Page Page Remove this Part LIST/EXPLODED Drawing from the Manual Part List-Model No. WESY74091 Qty Description16 x 2 1/4 Bolt Backrest Nylon Locknut Exploded Drawing-Model No. WESY74091 R0101A
Top Page Image Contents