Weider 740 user manual Bolt 12 and a 3/8 Nylon Locknut 21. Note, Spacer

Page 13

23.Wrap the Long Cable (23) around a 3 1/2” Pulley (15) in the direction shown.

Attach the 3 1/2” Pulley (15) and a Cable Trap (66) to the to the lower hole in the “I”-Plates (20) with a 3/8”

x 2” Bolt (12) and a 3/8” Nylon Locknut (21). Note:

Make sure the Cable Trap is oriented as shown.

24.Wrap the Long Cable (23) around a 3 1/2” Pulley (15) in the direction shown.

Attach the 3 1/2” Pulley (15) and a Cable Trap (66) to the indicated hole in the welded bracket on the Base

(4)with a 3/8” x 2” Bolt (12) and a 3/8” Nylon Locknut

(21).Note: Make sure the Cable Trap is oriented as shown.

25.Wrap the Long Cable (23) around a 3 1/2” Pulley (15) in the direction shown.

Attach the 3 1/2” Pulley (15) to the indicated side of

the Pulley Bracket (57) by using the 3/8” x 2 1/2” Bolt (60) and the 3/8” Nylon Jamnut (22) attached in step

21.Note: Make sure the Pulley Bracket is oriented exactly as shown and that the Pulley is attached on the indicated side.

26.Wrap the Long Cable (23) around a 3 1/2” Pulley (15) in the direction shown.

Attach the 3 1/2” Pulley (15) to the indicated side of

the Upright (42) with a 3/8” x 3” Bolt (72), a 3/8” Flat

Washer (9) and a 3/8” Nylon Jamnut (22).Note:

Make sure the Long Cable is between the Pulley and the Spacer on the Upright/Base.

23
	20
		21
	15
12		66
	23
24
		21
	4
		15
12	66	23
		23
25		57
60		57
60
15		23
		23
22
26
		42
		22
23		9
		9
15
		Spacer
72

13

Image 13

Contents Serial Number Decal Model No. WESY74091 Serial NoLimited Warranty Table of ContentsMake sure the cables remain on the pulleys Important PrecautionsKeep hands and feet away from moving parts Before You Begin Using the weight systemTo make the assembly process as smooth as possi AssemblyTo complete the process over a couple of evenings See the inset drawing Locate and open the parts bag labeled Frame AssemblyBolts with two 5/16 Nylon Locknuts Tighten the Nylon Locknuts yetDo not tighten Nylon Locknuts3 yet Place the Top Frame 55 on top of the UprightSlot FrameTop Frame Top Frame Weight Guide TubeLocate and open the parts bag labeled ARM Make sure the welded tab on the Press FrameTion of the welded bracket a on each Arm Short Cable 58 is between the Pulley 15 Locate the parts bag labeled Cable AssemblyBolt 12 and a 3/8 Nylon Locknut Cable Trap is oriented as shown8 x 1 Bolt 59, a 3/8 Plain Nut 56 and a 3/8 Spacer15b Ing the following steps. Note Make sure the Pulley Onto the Bolt to prevent the Pulley from falling off durView from behind From Pulley To Pulley BracketMake sure the Cable Trap is oriented as shown Bolt 12 and a 3/8 Nylon Locknut 21. NoteSpacer To the Seat 13 with two 1/4 x 3/4 Screws Shooting and Maintenance on Cable Diagrams76, 87 1/2 Long Cable58, 126 1/4 Cise will be reduced Changing the Weight Setting AdjustmentAdjusting the Arms for Butterfly or Press Exercises Attaching the Lat Bar to the Pulley StationCable and re-install it Trouble-shooting and MaintenanceStation Lever Weight Resistance ChartTop Part No R0101A Ordering Replacement PartsWESY74091 R0101A Remove this Part Identification Chart from the ManualPart Identification Chart-WESY74091 Page Page Remove this Part LIST/EXPLODED Drawing from the Manual Qty Description Part List-Model No. WESY7409116 x 2 1/4 Bolt Backrest Nylon Locknut Exploded Drawing-Model No. WESY74091 R0101A