Whirlpool W10235934A Installation Instructions, Remove Transport System, Connect the Inlet Hoses

Page 8

INSTALLATION INSTRUCTIONS

Remove Transport System

WARNING

Excessive Weight Hazard

Use two or more people to move and install washer. Failure to do so can result in back or other injury.

IMPORTANT: Position the washer so that the rear of the washer is within approximately 3 ft (900 mm) of its final location.

There are 4 transport bolts in the rear panel of the washer that support the suspension system during transportation. These bolts also retain the power cord inside the washer until the bolts are removed.

1.On the back of the washer, loosen the 4 transport bolts using a 13 mm wrench.

2.Once the bolt is loose, move it to the center of the hole and completely pull out the bolt, including the plastic spacer covering the bolt.

3.Once all 4 bolts are removed, discard the bolts and spacers. Then pull the power cord through the opening of the rear panel and close the hole with the attached cap.

4.Cover the bolt holes with the 4 transport bolt hole plugs.

NOTE: If the washer is to be transported at a later date, call your local service center. To avoid suspension and structural damage, your machine must be properly set up for relocation by a certified technician.

Connect the Inlet Hoses

Insert new flat washers (supplied) into each end of the inlet hoses. Firmly seat the washers in the couplings.

AB

A.Coupling

B.Washer

Connect the inlet hoses to the water faucets

Make sure washer drum is empty and flat washers have been placed into hose couplings.

1.Attach a hose to the hot water faucet. Screw on coupling by hand until it is seated on the washer.

2.Attach a hose to the cold water faucet. Screw on coupling by hand until it is seated on the washer.

3.Using pliers, tighten the couplings with an additional two-thirds turn.

NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can result.

Clear the water lines

Run water through both faucets and inlet hoses, into a laundry tub, drainpipe or bucket, to get rid of particles in the water lines that might clog the inlet valve screens.

Check the temperature of the water to make sure that the hot water hose is connected to the hot water faucet and that the cold water hose is connected to the cold water faucet.

8

Image 8
Contents W10235934A Use & Care GuideGuide d’utilisation et d’entretien Table DES Matières Washer Safety Your safety and the safety of others are very importantInstallation Requirements Tools and PartsOptions Location RequirementsInstallation clearances Washer DimensionsRecessed area or closet installation Recessed or closet installation Washer on pedestalDrain System Standpipe drain system wall or floor views a & BLaundry tub drain system view C Floor drain system view DElectrical Requirements Installation Instructions Remove Transport SystemConnect the Inlet Hoses Connect the inlet hoses to the water faucetsFloor drain Route the Drain HoseSecure the Drain Hose Complete Installation Level the WasherFeatures and Benefits Using the Proper Detergent Washer USEStarting Your Washer First Wash Cycle Without LaundryUsing the Dispenser Pausing or RestartingMain Wash detergent compartment Chlorine bleach compartmentCycles Changing Cycles and OptionsStatus Lights Preset Cycle Settings Hand Wash Clean WasherCycle Estimated Wash Temp Spin Speed Time SanitaryTemperature Guide Normal SoundsOptions and Modifiers Auto Temp ControlLaundry Guide Cycle Suggested Load Type Available OptionsLaundry Tips LoadingStain Removal Guide StainUse suggested Stain Use Liquid Chlorine or Color-Safe Bleach Wash Cycle Whitest Whites InkCleaning Your Washer Begin procedureWasher Care Always do the following to maintain washer freshnessNon-use or vacation care Water Inlet HosesVacation, Storage, and Moving Care Troubleshooting Washer and ComponentsWasher Operation When the washer stops working Are the touch pad buttons not responding?Washer won’t dispense Is the washer level? Has the drawer dispensed detergent?Clothes Care Assistance or Service If you need replacement partsU.S.A CanadaLimited Warranty Items Excluded from WarrantyThis limited warranty does not cover Disclaimer of Implied WarrantiesSécurité DE LA Laveuse Votre sécurité et celle des autres est très importanteOutillage et pièces Exigences DinstallationExigences demplacement Dégagements de séparation à respecter Dimensions de la laveuseInstallation dans un encastrement ou placard Espacement recommandé pour l’installation dans un placard Système de vidangeSystème de vidange avec évier de buanderie vue C Système de vidange au plancher vue DSpécifications électriques Pour une laveuse raccordée en permanenceInstructions Dinstallation Élimination des accessoires de transportRaccordement des tuyaux dalimentation Connecter les tuyaux dalimentation aux robinets deauAcheminement du tuyau de vidange Égout au plancherConnecter les tuyaux d’alimentation à la laveuse Retirer le tuyau de vidange de la laveuseAchever l’installation Immobilisation du tuyau de vidangeRéglage de l’aplomb de la laveuse RemarquesCaractéristiques ET Avantages Pour tous les programmes de lavage Pour charger la laveuse Utilisation DE LA LaveusePremier programme de lavage sans linge à laver Utilisation du distributeur Compartiment pour détergent du lavage principalChoix du détergent approprié Pour remplir les compartiments du distributeurPause ou remise en marche Modification des programmes et optionsTémoins lumineux Compartiment de lagent de blanchimentProgrammes HrminSons normaux Guide de température Commande automatique de la températureOptions et modificateurs Guide de lessivage Programme Type DE Charge Suggéré Options DisponiblesConseils DE Lessivage ChargementGuide pour lélimination des taches Début de la procédure Entretien DE LA LaveuseNettoyage de la laveuse Tuyaux darrivée deau Entreposage ou un déménagementDépannage La laveuse et ses composantsLe programme de la laveuse ne démarre pas Fonctionnement de la laveuseLa laveuse ne se met pas en marche La laveuse cesse de fonctionner Quand la laveuse cesse-t-elle de fonctionnerLa laveuse n’effectue pas la distribution La laveuse ne se remplit pasSoin des vêtements Le moteur de la laveuse surchauffeBruits, vibrations, et durées La laveuse vibre Changements dans la durée du programme/programme trop longAvez-vous surchargé la laveuse? Assistance OU Service Aux États-UnisAu Canada Si vous avez besoin de pièces de rechangeLa présente garantie limitée ne couvre pas Garantie LimitéeÉléments Exclus DE LA Garantie Page Whirlpool Corporation

W10235934A specifications

The Whirlpool W10235934A is a high-performance appliance designed to enhance the efficiency and convenience of household tasks, specifically in laundry care. As a key component within Whirlpool’s extensive lineup of washers, this model integrates a range of features and technologies that cater to modern consumer needs.

One of the standout characteristics of the W10235934A is its advanced sensor technology. This feature intelligently monitors the level of moisture in clothes, adjusting the drying time as needed to prevent over-drying and ensure optimal fabric care. By preventing excessive heat exposure, this technology not only extends the lifespan of garments but also helps reduce energy consumption, making it an eco-friendly choice for environmentally conscious consumers.

The W10235934A is designed with a focus on user convenience. Its intuitive controls and user-friendly interface enable users to easily select drying cycles suited for various fabric types, ensuring that every piece of clothing gets the care it needs. Whether it’s delicates, regular cottons, or heavy towels, this appliance provides tailored drying options to meet the specific requirements of different fabric blends.

Another key feature of the Whirlpool W10235934A is its large capacity. With ample space to accommodate substantial laundry loads, this appliance is ideal for families or individuals with busy lifestyles. The spacious design reduces the frequency of laundry days, allowing users to manage their time more effectively. Moreover, this model can tackle bulky items like comforters and blankets with ease, proving its versatility in various laundry situations.

The durability and design of the W10235934A further underline its quality. Made with premium materials, this appliance is built to withstand the rigors of daily use. Its sleek and modern aesthetic complements a range of home decors, making it a stylish addition to any laundry room.

In terms of maintenance, the Whirlpool W10235934A boasts features that simplify upkeep. The lint filter is designed for easy access and cleaning, ensuring optimal performance while promoting safety by preventing lint buildup, which is a common cause of dryer fires.

Overall, the Whirlpool W10235934A stands out in the crowded appliance market with its blend of advanced technology, user-centric design, and powerful performance. For anyone seeking a reliable and efficient drying solution, this model represents a noteworthy investment for modern living.