Cabletron Systems EMM-E6 manual Cabletron Software Program License

Page 5

Notice

CABLETRON SOFTWARE PROGRAM LICENSE

1.LICENSE. You have the right to use only the one (1) copy of the Program provided in this package subject to the terms and conditions of this License Agreement.

You may not copy, reproduce or transmit any part of the Program except as permitted by the Copyright Act of the United States or as authorized in writing by Cabletron.

2.OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the Program.

3.APPLICABLE LAW. This License Agreement shall be interpreted and governed under the laws and in the state and federal courts of New Hampshire. You accept the personal jurisdiction and venue of the New Hampshire courts.

EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY

1.EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in writing, Cabletron makes no warranty, expressed or implied, concerning the Program (including its documentation and media).

CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO YOU BY CABLETRON IN WRITING, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE ACCOMPANYING WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.

2.NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS) ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR ON THE DURATION OR LIMITATION OF IMPLIED WARRANTIES, IN SOME INSTANCES THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU.

UNITED STATES GOVERNMENT RESTRICTED RIGHTS

The enclosed product (a) was developed solely at private expense; (b) contains “restricted computer software” submitted with restricted rights in accordance with Section 52227-19 (a) through (d) of the Commercial Computer Software - Restricted Rights Clause and its successors, and (c) in all respects is proprietary data belonging to Cabletron and/or its suppliers.

For Department of Defense units, the product is licensed with “Restricted Rights” as defined in the DoD Supplement to the Federal Acquisition Regulations, Section 52.227-7013 (c) (1) (ii) and its successors, and use, duplication, disclosure by the Government is subject to restrictions as set forth in subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at

252.227-7013. Cabletron Systems, Inc., 35 Industrial Way, Rochester, New Hampshire 03867-0505.

EMM-E6 Installation Guide

iii

Image 5
Contents EMM-E6 Ethernet Bridge Management Module Installation GuidePage EMM-E6 Installation Guide DOC Notice Cabletron Software Program License Declaration of Conformity Contents Adding Epims EMM-E6 Overview HOW to USE this ManualChapter Introduction Introduction Following conventions are used throughout this document Document ConventionsGetting Help Related DocumentsFaceplate Chapter Controls and IndicatorsInternal Components Internal Components Epim Connector Pins Ldram Simm Slot Lanview Leds Reset CPU B a Stby RCV XMT CLNLanview Leds EMM-E6 Installation Guide Unpacking the EMM-E6 Chapter InstallationPerform a second visual inspection of the module EMM-E6 Dip Switches Setting Mode SwitchesEMM-E6 Installation Guide PRE-INSTALLATION Test Pre-Installation Test Configuration Install the EMM-E6 into the MMAC-FNB backplane as follows InstallationModule Guide Channels Reset CPU B a Stby RCV XMT CLN Connecting a 10BASE-T Segment to an EPIM-T Connecting to the NetworkPosition X crossed over RX+ TX+ Position = Not crossed over Cable Pinouts RJ45 Port Connecting a 10BASE-F Segment to an EPIM-F2 or EPIM-F3 ST Connector Insertion Connecting a 10BASE-F Segment to an EPIM-F1 SMA Connector Insertion EPIM-A Connecting an AUI Segment to an EPIM-X orConnecting a 10BASE2 Segment to an EPIM-C 10 BNC Connector Insertion 11 Backplane Test Configuration Backplane TestUsing Lanview Leds Chapter TroubleshootingTroubleshooting Using Lanview Leds Troubleshooting Checklist Troubleshooting Checklist EPIM-A Using the Reset Switch EMM-E6 Installation Guide Operating Specifications Appendix a SpecificationsPhysical Specifications COM Port Pinout Environmental RequirementsCertification Appendix B Upgrading the EMM-E6 Locating Brim ConnectorsAdding Epims To install an EPIM, perform the following stepsLocating SIMMs Simm UpgradesFigure B-3, refer to the procedures below Installing SIMMs1 10BASE-T Twisted Pair Network Appendix C Ethernet Cabling RequirementsNetwork Requirements Appendix C Ethernet Cabling Requirements Multimode Fiber Optic Network Single Mode Fiber Optic Network Transceiver Requirements 4 10BASE2 Coaxial Cable NetworkEMM-E6 Installation Guide Numerics IndexIndex-2 EMM-E6 Installation Guide Lanview LEDs EMM-E6Installation
Related manuals
Manual 118 pages 2.72 Kb