Cabletron Systems EMM-E6 manual Related Documents, Getting Help

Page 12

Chapter 1: Introduction

1.4 RELATED DOCUMENTS

Use the following manuals to supplement the procedures and other technical data provided in this manual. This manual references procedures in these manuals, where appropriate, but does not repeat them.

Cabletron Systems MMAC Overview and Setup Guide

Cabletron Systems EMM-E6 Local Management Guide

Cabletron Systems SPECTRUM Element Manager User’s Guide

1.5 GETTING HELP

If you need additional support related to this device, or if you have any questions, comments, or suggestions concerning this manual, contact Cabletron Systems Technical Support:

By phone

(603) 332-9400

 

Monday – Friday; 8 A.M. – 8 P.M. Eastern Time

By CompuServe

GO CTRON from any ! prompt

By Internet mail

support@ctron.com

By FTP

ctron.com (134.141.197.25)

Login

anonymous

Password

your email address

Before calling Cabletron Systems Technical Support, have the following information ready:

A description of the failure

A description of any action(s) already taken to resolve the problem (e.g., changing mode switches, rebooting the unit, etc.)

A description of your network environment (layout, cable type, etc.)

Network load and frame size at the time of trouble (if known)

The serial and revision numbers of all Cabletron Systems products in the network

The device history (i.e., have you returned the device before, is this a recurring problem, etc.)

Any previous Return Material Authorization (RMA) numbers.

1-4

EMM-E6 Installation Guide

Image 12
Contents Management Module Installation Guide EMM-E6 Ethernet BridgePage EMM-E6 Installation Guide DOC Notice Cabletron Software Program License Declaration of Conformity Contents Adding Epims HOW to USE this Manual Chapter IntroductionEMM-E6 Overview Introduction Document Conventions Following conventions are used throughout this documentRelated Documents Getting HelpChapter Controls and Indicators FaceplateInternal Components Internal Components Epim Connector Pins Ldram Simm Slot Reset CPU B a Stby RCV XMT CLN Lanview LedsLanview Leds EMM-E6 Installation Guide Chapter Installation Unpacking the EMM-E6Perform a second visual inspection of the module Setting Mode Switches EMM-E6 Dip SwitchesEMM-E6 Installation Guide PRE-INSTALLATION Test Pre-Installation Test Configuration Installation Install the EMM-E6 into the MMAC-FNB backplane as followsModule Guide Channels Reset CPU B a Stby RCV XMT CLN Connecting to the Network Connecting a 10BASE-T Segment to an EPIM-TPosition X crossed over RX+ TX+ Position = Not crossed over Cable Pinouts RJ45 Port Connecting a 10BASE-F Segment to an EPIM-F2 or EPIM-F3 ST Connector Insertion Connecting a 10BASE-F Segment to an EPIM-F1 SMA Connector Insertion Connecting an AUI Segment to an EPIM-X or EPIM-AConnecting a 10BASE2 Segment to an EPIM-C 10 BNC Connector Insertion Backplane Test 11 Backplane Test ConfigurationChapter Troubleshooting Using Lanview LedsTroubleshooting Using Lanview Leds Troubleshooting Checklist Troubleshooting Checklist EPIM-A Using the Reset Switch EMM-E6 Installation Guide Appendix a Specifications Physical SpecificationsOperating Specifications Environmental Requirements CertificationCOM Port Pinout Locating Brim Connectors Appendix B Upgrading the EMM-E6To install an EPIM, perform the following steps Adding EpimsSimm Upgrades Locating SIMMsInstalling SIMMs Figure B-3, refer to the procedures belowAppendix C Ethernet Cabling Requirements Network Requirements1 10BASE-T Twisted Pair Network Appendix C Ethernet Cabling Requirements Multimode Fiber Optic Network Single Mode Fiber Optic Network 4 10BASE2 Coaxial Cable Network Transceiver RequirementsEMM-E6 Installation Guide Index NumericsIndex-2 EMM-E6 Installation Guide EMM-E6 Lanview LEDsInstallation
Related manuals
Manual 118 pages 2.72 Kb