Cabletron Systems EMM-E6 manual Declaration of Conformity

Page 6

Notice

DECLARATION OF CONFORMITY

Application of Council Directive(s): 89/336/EEC 73/23/EEC

Manufacturer’s Name: Cabletron Systems, Inc.

Manufacturer’s Address: 35 Industrial Way

PO Box 5005

Rochester, NH 03867

European Representative Name: Mr. J. Solari

European Representative Address: Cabletron Systems Limited

Nexus House, Newbury Business Park

London Road, Newbury

Berkshire RG13 2PZ, England

Conformance to Directive(s)/Product Standards: EC Directive 89/336/EEC

EC Directive 73/23/EEC

EN 55022

EN 50082-1

EN 60950

Equipment Type/Environment: Networking Equipment, for use in a

Commercial or Light Industrial Environment.

We the undersigned, hereby declare that the equipment packaged with this notice conforms to the above directives.

Manufacturer

Legal Representative in Europe

Mr. Richard Michaud

Mr. J. Solari

___________________________________

___________________________________

Full Name

Full Name

Manager of Engineering Services

Managing Director - E.M.E.A.

___________________________________

___________________________________

Title

Title

Rochester, NH, USA

Newbury, Berkshire, England

___________________________________

___________________________________

Location

Location

iv

EMM-E6 Installation Guide

Image 6
Contents Management Module Installation Guide EMM-E6 Ethernet BridgePage EMM-E6 Installation Guide DOC Notice Cabletron Software Program License Declaration of Conformity Contents Adding Epims HOW to USE this Manual Chapter IntroductionEMM-E6 Overview Introduction Document Conventions Following conventions are used throughout this documentRelated Documents Getting HelpChapter Controls and Indicators FaceplateInternal Components Internal Components Epim Connector Pins Ldram Simm Slot Reset CPU B a Stby RCV XMT CLN Lanview LedsLanview Leds EMM-E6 Installation Guide Chapter Installation Unpacking the EMM-E6Perform a second visual inspection of the module Setting Mode Switches EMM-E6 Dip SwitchesEMM-E6 Installation Guide PRE-INSTALLATION Test Pre-Installation Test Configuration Installation Install the EMM-E6 into the MMAC-FNB backplane as followsModule Guide Channels Reset CPU B a Stby RCV XMT CLN Connecting to the Network Connecting a 10BASE-T Segment to an EPIM-TPosition X crossed over RX+ TX+ Position = Not crossed over Cable Pinouts RJ45 Port Connecting a 10BASE-F Segment to an EPIM-F2 or EPIM-F3 ST Connector Insertion Connecting a 10BASE-F Segment to an EPIM-F1 SMA Connector Insertion Connecting an AUI Segment to an EPIM-X or EPIM-AConnecting a 10BASE2 Segment to an EPIM-C 10 BNC Connector Insertion Backplane Test 11 Backplane Test ConfigurationChapter Troubleshooting Using Lanview LedsTroubleshooting Using Lanview Leds Troubleshooting Checklist Troubleshooting Checklist EPIM-A Using the Reset Switch EMM-E6 Installation Guide Appendix a Specifications Physical SpecificationsOperating Specifications Environmental Requirements CertificationCOM Port Pinout Locating Brim Connectors Appendix B Upgrading the EMM-E6To install an EPIM, perform the following steps Adding EpimsSimm Upgrades Locating SIMMsInstalling SIMMs Figure B-3, refer to the procedures belowAppendix C Ethernet Cabling Requirements Network Requirements1 10BASE-T Twisted Pair Network Appendix C Ethernet Cabling Requirements Multimode Fiber Optic Network Single Mode Fiber Optic Network 4 10BASE2 Coaxial Cable Network Transceiver RequirementsEMM-E6 Installation Guide Index NumericsIndex-2 EMM-E6 Installation Guide EMM-E6 Lanview LEDsInstallation
Related manuals
Manual 118 pages 2.72 Kb