Cabletron Systems EMM-E6 manual Appendix a Specifications, Physical Specifications

Page 49

APPENDIX A

SPECIFICATIONS

This appendix lists some of the important specifications and specified requirements for the EMM-E6. Cabletron Systems reserves the right to change these specifications at any time and without notice.

A.1 PHYSICAL SPECIFICATIONS

Dimensions:

29.21 H x 7.64 W x 34.07 D cm

 

(11.5 H x 3 W x 13.4 D in)

Weight (unit):

1.25 kg (2.75 lbs)

Weight (as shipped):

1.74 kg (3.83 lbs)

A.2 OPERATING SPECIFICATIONS

Internal Processor(s):

Intel 80960

Ethernet Controller:

4 DP83932 Controllers

Shared Memory:

4 MB (Expandable to 12 MB)

Read Only Memory (NVRAM):

128 K

FLASH Memory:

2 MB (Expandable to 14 MB)

CPU Memory (Local Memory):

8 MB (4 MB + 4 MB SIMM)

 

(Expandable to 12 MB)

Filtering Table:

8,191 entries maximum

Aging Time:

5 minutes (default)

EMM-E6 Installation Guide

A-1

Image 49
Contents EMM-E6 Ethernet Bridge Management Module Installation GuidePage EMM-E6 Installation Guide DOC Notice Cabletron Software Program License Declaration of Conformity Contents Adding Epims Chapter Introduction HOW to USE this ManualEMM-E6 Overview Introduction Following conventions are used throughout this document Document ConventionsGetting Help Related DocumentsFaceplate Chapter Controls and IndicatorsInternal Components Internal Components Epim Connector Pins Ldram Simm Slot Lanview Leds Reset CPU B a Stby RCV XMT CLNLanview Leds EMM-E6 Installation Guide Unpacking the EMM-E6 Chapter InstallationPerform a second visual inspection of the module EMM-E6 Dip Switches Setting Mode SwitchesEMM-E6 Installation Guide PRE-INSTALLATION Test Pre-Installation Test Configuration Install the EMM-E6 into the MMAC-FNB backplane as follows InstallationModule Guide Channels Reset CPU B a Stby RCV XMT CLN Connecting a 10BASE-T Segment to an EPIM-T Connecting to the NetworkPosition X crossed over RX+ TX+ Position = Not crossed over Cable Pinouts RJ45 Port Connecting a 10BASE-F Segment to an EPIM-F2 or EPIM-F3 ST Connector Insertion Connecting a 10BASE-F Segment to an EPIM-F1 SMA Connector Insertion EPIM-A Connecting an AUI Segment to an EPIM-X orConnecting a 10BASE2 Segment to an EPIM-C 10 BNC Connector Insertion 11 Backplane Test Configuration Backplane TestUsing Lanview Leds Chapter TroubleshootingTroubleshooting Using Lanview Leds Troubleshooting Checklist Troubleshooting Checklist EPIM-A Using the Reset Switch EMM-E6 Installation Guide Physical Specifications Appendix a SpecificationsOperating Specifications Certification Environmental RequirementsCOM Port Pinout Appendix B Upgrading the EMM-E6 Locating Brim ConnectorsAdding Epims To install an EPIM, perform the following stepsLocating SIMMs Simm UpgradesFigure B-3, refer to the procedures below Installing SIMMsNetwork Requirements Appendix C Ethernet Cabling Requirements1 10BASE-T Twisted Pair Network Appendix C Ethernet Cabling Requirements Multimode Fiber Optic Network Single Mode Fiber Optic Network Transceiver Requirements 4 10BASE2 Coaxial Cable NetworkEMM-E6 Installation Guide Numerics IndexIndex-2 EMM-E6 Installation Guide Lanview LEDs EMM-E6Installation
Related manuals
Manual 118 pages 2.72 Kb