Alliance Laundry Systems SVN255P, UVN255P installation instructions Tilt models, Tilt Models

Page 31

Tilt models

31

 

 

4.TILT MODELS

ATTENTION!

4.1. TILT models specific safety instructions

During the assembling and operation verification of the TILT system strictly follow the safety precautions indicated at the beginning of this manual.

The transport and assembling operations of tilt components must be carried out by the Authorised Technical Service.

Due to mass weight, be especially careful when carrying out these operations. Remember that weights and measures of TILT models can be found in the Installation specifications, section 1.4.

To avoid any risk during the operation of verification of the TILT SYSTEM please follow these instructions:

Keep away of the rear of the washer during the tilt movement. Because of the washer's tilting movement, there is crushing and shearing hazard between the tilting elements and the building elements.

The TILT SYSTEM has JUST been designed to facilitate the washer's loading and unloading operations.

DO NOT USE the washer until all the guards are properly located and adjusted

In particular take special care to the tilt hinge guards.

DO NOT MISLEAD NOR CANCEL THE POSITION DETECTORS located on the machine brackets.

DO NOT MISLEAD NOR CANCEL THE PUSH-BUTTON that activate the drum's rotation with the door open.

The pressure of the pneumatic circuit specific for tilting is controlled by a pressure regulator located on the electrical panel, with a fixed adjustment. DO NOT MODIFY NOR MANIPULATE THIS REGULATOR.

Because of the facility of rotating the drum with door open, during loading and unloading operations NEVER MORE THAN ONE PERSON WILL OPERATE WITH THE MACHINE.

The washer is protected against possible incorrect handling, so machine must be in horizontal position before selecting a tilting movement or starting a wash program.

4.2.TILT system description

Set of components that, using the strength of two pneumatic actuators, permit a double tilt movement for the whole of the machine, forwards and backwards to easily load and unload the washer.

Four position detectors, one at each washer's supports, ensure the correct operation of the tilt system, and a balanced position during the wash cycle.

The washer's electrical control permits the drum's rotation and reverse by two hold-to-run push-buttons and the fabric soaking when loaded to reduce the volume.

The bath used to soaking the linen is not kept inside the washer when the wash cycle starts.

4.3.TILT system specific protection elements

Fixed guards: Covers at the machine sides. Protect the user from the contact with dangerous points and spattering.

Moving guards: Front and side covers that permit the washer tilting. Protect the user from the contact with dangerous points and spattering.

Pneumatic actuator limit switches. Prevent the excessive expansion of actuators and the excessive tilting of the washer.

Position detector microswitches. Control the position of the tilt system.

Pneumatic actuator pressure regulators. Limit the air pressure of pneumatic actuators. Adjustment value: 5 kg/cm2 (71 PSI). DO NOT MODIFY NOR MANIPULATE THIS REGULATOR.

4.4.Washer location

To determine the washer location bear in mind the machine's tilting movements. Refer to movement values on figure 29 (section 4.5)

 

Cod. G522433

© Copyright 2009, Alliance Laundry System LLC – DO NOT COPY OR TRANSMIT

Rev. 00/0510

Image 31
Contents Serial # Shipping date UVN255P1520001 SVN255PDo not try to open the washer’s door if the drum is moving Safety InstructionsSafety Instructions Copyright 2009, Alliance Laundry System LLC Replacement PartsCustomer Service Electric risk High temperature riskReason for which only Original Spare Parts Must be Used ∙ Epdm and NBRIndex Technical Information IndexTechnical Information Necessary tools for installationMachine accessories Technical InformationInstallation Specifications General specificationsMachine connections Connections Brackets specific values for USA / Canada Electrical requirementsTransporting crated machines Transportation and locationTransportation and Location Transport of machineReleasing the security lock Washer location. Conditions Installation on NON Solid Grounds and Upper FloorsLocation specifications fig Installing more than one washerTilt Models Removal of shipping bracesTransportation and location A. Drain to the drain box Most recommended option Installation18Installation DrainWater inlets Installation19Siphonage Contamination Prevention Installation20 Conductor Installation21Installation characteristics Electrical requirements Previous requirementsPE/GND Installation22Machine electrical connection Installation characteristics Installation23Steam connection Connection of the machine to the steam installation fig Installation24Steam connection in Tilt models External dosing equipment connection to the washer Installation25Compressed air connection figure External dosingLock the Covers Correctly Potential Free Relay Contacts Installation26Use of four dosing signals Once the conductor connection is done, ReplaceRelay Contacts Powered from the Washer Control Circuit Installation27Board Installation28Signal DosingExternal dosing hoses connection InstallationInitial start-up Installation30Specific verification of Tilt models Tilt Models Tilt modelsMax Water inlet installation proposalTools to assemble the tilt system Tilt system assemblyAssembly Instructions for the Tilt System Accessories Parts of the tilt system assemblyTilt hinge assembly Position detectors assembly and adjustment figure Assembling Tilt system guards figure

SVN255P, UVN255P specifications

Alliance Laundry Systems has long been recognized for its commitment to innovation and quality in the laundry industry, and the launch of the UVN255P and SVN255P models reinforces this reputation. Designed primarily for commercial laundry applications, these units bring robust performance, efficiency, and advanced technology to heavy-duty environments.

At the core of the UVN255P and SVN255P models is their impressive washing capacity. With a significant load size capability, these machines are perfect for laundromats, hotels, and other high-demand facilities, enabling operators to process more laundry in less time. This capacity not only enhances productivity but also optimizes labor costs, allowing for greater operational efficiency.

One standout feature of both models is their user-friendly control interface. The intuitive controls are designed to simplify operation, minimizing the learning curve for new users. Alongside this, the machines offer programmable cycles that can be tailored to suit various fabrics and cleaning requirements. This flexibility ensures that the laundry process is not only efficient but also maintains the integrity of delicate items, as the right settings can be applied with ease.

Energy efficiency is another hallmark of the UVN255P and SVN255P. Both models are engineered to reduce water and energy consumption, aligning with sustainability goals that are increasingly important in today’s business environment. As a result, these machines not only contribute to a lower carbon footprint but also promise significant savings on utility bills, ultimately enhancing profitability for businesses.

Durability is also a key characteristic of these models, crafted with robust materials that withstand the rigors of constant use in commercial settings. The stainless steel construction not only ensures longevity but also makes maintenance simpler and quicker, minimizing downtime for facilities reliant on continued operation.

Furthermore, both models incorporate advanced technology features such as real-time performance monitoring and diagnostic tools. These capabilities allow operators to troubleshoot issues swiftly, reduce machine downtime, and maintain optimal performance levels.

In summary, the Alliance Laundry Systems UVN255P and SVN255P stand out in the commercial laundry market due to their high capacity, energy efficiency, user-friendly controls, and durable build. These features come together to provide businesses with a powerful solution that meets the demanding needs of modern laundry operations, ensuring that they can deliver high-quality service to their customers with confidence.