Alliance Laundry Systems UVN255P, SVN255P Installation30, Initial start-up

Page 30

Installation30

3.7.Initial start-up

THE WASHER MUST BE PUT INTO SERVICE BY AN AUTHORIZED SERVICE TECHNICIAN.

BEFORE THE STARTING-UP OF THE WASHER, BEAR IN MIND ALL THE SAFETY INSTRUCTIONS AT THE BEGINNING SECTION OF THIS MANUAL.

Before the initial starting, make sure that you accomplish the following points:

 

∙ Remove all packing materials. (Break them down in order to appropriately recycle them).

 

∙ Remove all tools used during the installation.

 

∙ Verify that all accessories have been removed from the

 

drum interior.

 

∙ Assemble the protective elbow at the steam exhaust facing

 

upwards and fastened with the flange (fig. 27)

 

∙ Verify the correct installation of all the accessories

 

necessary for the washer operation.

 

∙ Check that the electrical installation corresponds with the

 

voltage and the frequency of the machine.

 

∙ Verify that the four washer feet come in contact with the floor.

 

∙ Verify that all the shipping restraints are removed and that all

 

the covers are properly locked.

 

∙ Connect all the water, steam (steam heated washers),

fig. 27

power and air compressed inlets (following machine model),

according to technical specifications.

 

∙Open the manual water inlet valves (steam and compressed air, following the models) and check for any leaks around the manual flow valves and connection couplings.

∙Connect the electricity supply.

∙Check the operation (it is recommended to use the TEST program).

∙Keep the manual in a safe place and in good condition for its possible consultation.

∙Before washing clothes for the first time we recommend to run a complete cycle with detergent (1/4 the normal recommended amount).

Specific verification of TILT models

Before starting the TILT system verification, refer to the Safety precautions specific for TILT models, at the beginning of chapter 4.

Open the washer door and activate the tilt system. Verify the following points.

∙Machine movements in the loading and unloading positions. The connections must allow the movement of the machine without damage or forced loops.

∙Loading and unloading movements mustn't place the drain outlet hose outside the drain box or drain manifold.

∙Tilt system limit switches must prevent the movement of the machine's rear supports while front supports are not in the rest position and vice versa.

∙The tilt supplement guards must always prevent the access to the machine base.

 

Cod. G522433

© Copyright 2009, Alliance Laundry System LLC – DO NOT COPY OR TRANSMIT

Rev. 00/0510

Page 29 Page 31
Image 30
Page 29 Page 31
Contents SVN255P UVN255P1520001 Serial # Shipping dateSafety Instructions Do not try to open the washer’s door if the drum is movingSafety Instructions Electric risk High temperature risk Replacement PartsCustomer Service Copyright 2009, Alliance Laundry System LLC∙ Epdm and NBR Reason for which only Original Spare Parts Must be UsedIndex Index Technical InformationTechnical Information Necessary tools for installationMachine accessories Technical InformationGeneral specifications Installation SpecificationsMachine connections Connections Electrical requirements Brackets specific values for USA / CanadaTransport of machine Transportation and locationTransportation and Location Transporting crated machinesReleasing the security lock Installation on NON Solid Grounds and Upper Floors Washer location. ConditionsInstalling more than one washer Location specifications figRemoval of shipping braces Tilt ModelsTransportation and location Drain Installation18Installation A. Drain to the drain box Most recommended optionInstallation19 Water inletsSiphonage Contamination Prevention Installation20 Electrical requirements Previous requirements Installation21Installation characteristics ConductorInstallation22 PE/GNDMachine electrical connection Installation23 Installation characteristicsSteam connection Installation24 Connection of the machine to the steam installation figSteam connection in Tilt models External dosing Installation25Compressed air connection figure External dosing equipment connection to the washerOnce the conductor connection is done, Replace Installation26Use of four dosing signals Lock the Covers Correctly Potential Free Relay ContactsInstallation27 Relay Contacts Powered from the Washer Control CircuitDosing Installation28Signal BoardInstallation External dosing hoses connectionInstallation30 Initial start-upSpecific verification of Tilt models Tilt models Tilt ModelsWater inlet installation proposal MaxParts of the tilt system assembly Tilt system assemblyAssembly Instructions for the Tilt System Accessories Tools to assemble the tilt systemTilt hinge assembly Position detectors assembly and adjustment figure Assembling Tilt system guards figure

SVN255P, UVN255P specifications

Alliance Laundry Systems has long been recognized for its commitment to innovation and quality in the laundry industry, and the launch of the UVN255P and SVN255P models reinforces this reputation. Designed primarily for commercial laundry applications, these units bring robust performance, efficiency, and advanced technology to heavy-duty environments.

At the core of the UVN255P and SVN255P models is their impressive washing capacity. With a significant load size capability, these machines are perfect for laundromats, hotels, and other high-demand facilities, enabling operators to process more laundry in less time. This capacity not only enhances productivity but also optimizes labor costs, allowing for greater operational efficiency.

One standout feature of both models is their user-friendly control interface. The intuitive controls are designed to simplify operation, minimizing the learning curve for new users. Alongside this, the machines offer programmable cycles that can be tailored to suit various fabrics and cleaning requirements. This flexibility ensures that the laundry process is not only efficient but also maintains the integrity of delicate items, as the right settings can be applied with ease.

Energy efficiency is another hallmark of the UVN255P and SVN255P. Both models are engineered to reduce water and energy consumption, aligning with sustainability goals that are increasingly important in today’s business environment. As a result, these machines not only contribute to a lower carbon footprint but also promise significant savings on utility bills, ultimately enhancing profitability for businesses.

Durability is also a key characteristic of these models, crafted with robust materials that withstand the rigors of constant use in commercial settings. The stainless steel construction not only ensures longevity but also makes maintenance simpler and quicker, minimizing downtime for facilities reliant on continued operation.

Furthermore, both models incorporate advanced technology features such as real-time performance monitoring and diagnostic tools. These capabilities allow operators to troubleshoot issues swiftly, reduce machine downtime, and maintain optimal performance levels.

In summary, the Alliance Laundry Systems UVN255P and SVN255P stand out in the commercial laundry market due to their high capacity, energy efficiency, user-friendly controls, and durable build. These features come together to provide businesses with a powerful solution that meets the demanding needs of modern laundry operations, ensuring that they can deliver high-quality service to their customers with confidence.
Top Page Image Contents