Alliance Laundry Systems SVN255P, UVN255P installation instructions Safety Instructions

Page 3

Safety Instructions

3

 

 

16. WARNING!

MACHINE INSPECTION, FILTER CLEANING, MAINTENANCE, SERVICE OR PARTS REPLACEMENT

Before attempting any service or inspection of the washing machine:

Close and mechanically interlock the water supply valves and check that machine has COMPLETELY drained, parts have cooled down and that no pieces are in movement through inertia.

To reduce the risk of electrical shock:

COMPLETELY disconnect the machine from the original power source and check for accidental reconnection. MOVING THE ON SWITCH TO THE OFF POSITION IS NOT SUFFICIENT.

Disconnect the electrical power of the external dosing to the washing machine. These circuits are independent of the washer’s supply.

Wait a minimum of (5) five minutes after disconnection to ensure the elimination of residual voltage within the machine.

Failure to comply with this warning may result in serious injury.

17.NEVER START THE MACHINE NOR USE IT IN THE ABSENCE, INCORRECT POSITION OR MALFUNCTION OF:

COVERS (SAFETY GUARDS) AND PROTECTION

SAFETY DEVICES

CONTROL DEVICES

18.The room SHALL comply with the environment conditions (air venting, temperature, humidity...) specified in the Installation Instruction Handbook. NEVER INSTALL THE WASHING MACHINE in very humid environments or with water splashes.

19.DO NOT OPERATE the machine if it is suspected to be faulty, either visually, by noise or smell, or with missing or broken parts.

20.Machinestart-up SHALL be made by Authorised Service Technicians (refer to note 2).

21.Machine SHALL BE USED by qualified personnel (refer to note 1), 1 wholly familiar with the machine’s operation.

22.DO NOT allow children or people with handicaps incompatible to machine use to operate machine.

23.Every machine working with temperature has a fire hazard, take SPECIAL care. KEEP appliance area free from combustible materials and fire extinguishers should be PLACED near the machines and should be easily accessible to all laundry staff.

24.Delimitate danger areas and PREVENT public access to them with machine in operation. Do not expose yourself to the dispenser, drain and rear overflow steam exhaust.

25.On completion of the day's work, TURN OFF the manual supply valves and DISCONNECT the electrical power by the External Automatic Switch.

26.Always CONTACT an Authorised Service Technician or Licensed Installer (refer to notes 2 & 3) about any problems or conditions you do not understand.

27.For a safe operation, machine MUST be kept in a good environment, used and maintained properly. We recommend asking annually the Authorised Technical Service for a thorough overhaul (refer to note 2).

28.The Distributor (seller) IS OBLIGED to thoroughly train the operator during the starting-up.

IN THE EVENT OF THESE SAFETY INSTRUCTIONS AND ALL THE INFORMATION SUPPLIED IN THE CORRESPONDING MANUALS NOT BEING ADHERED TO, THE MANUFACTURER DECLINES ALL RESPONSIBILITY.

KEEP THESE INSTRUCTIONS

NOTES:

(1)Qualified Personnel refers to anyone who has read the Instructions Handbooks, has been trained and has a thorough understanding of the machine’s operation

(2)An Authorised Service Technician (AST) is one that has successfully completed training on the product by the manufacturer or a manufacturer Distributor.

(3)An Authorised Licensed Installer is one that is suitably qualified in the procedures and regulations applicable in that country.

 

Cod. G522433

© Copyright 2009, Alliance Laundry System LLC – DO NOT COPY OR TRANSMIT

Rev. 00/0510

Image 3
Contents Serial # Shipping date UVN255P1520001 SVN255PDo not try to open the washer’s door if the drum is moving Safety InstructionsSafety Instructions Copyright 2009, Alliance Laundry System LLC Replacement PartsCustomer Service Electric risk High temperature riskReason for which only Original Spare Parts Must be Used ∙ Epdm and NBRIndex Technical Information IndexTechnical Information Necessary tools for installationMachine accessories Technical InformationInstallation Specifications General specificationsMachine connections Connections Brackets specific values for USA / Canada Electrical requirementsTransporting crated machines Transportation and locationTransportation and Location Transport of machineReleasing the security lock Washer location. Conditions Installation on NON Solid Grounds and Upper FloorsLocation specifications fig Installing more than one washerTilt Models Removal of shipping bracesTransportation and location A. Drain to the drain box Most recommended option Installation18Installation DrainInstallation19 Water inletsSiphonage Contamination Prevention Installation20 Conductor Installation21Installation characteristics Electrical requirements Previous requirementsInstallation22 PE/GNDMachine electrical connection Installation23 Installation characteristicsSteam connection Installation24 Connection of the machine to the steam installation figSteam connection in Tilt models External dosing equipment connection to the washer Installation25Compressed air connection figure External dosingLock the Covers Correctly Potential Free Relay Contacts Installation26Use of four dosing signals Once the conductor connection is done, ReplaceRelay Contacts Powered from the Washer Control Circuit Installation27Board Installation28Signal DosingExternal dosing hoses connection InstallationInstallation30 Initial start-upSpecific verification of Tilt models Tilt Models Tilt modelsMax Water inlet installation proposalTools to assemble the tilt system Tilt system assemblyAssembly Instructions for the Tilt System Accessories Parts of the tilt system assemblyTilt hinge assembly Position detectors assembly and adjustment figure Assembling Tilt system guards figure

SVN255P, UVN255P specifications

Alliance Laundry Systems has long been recognized for its commitment to innovation and quality in the laundry industry, and the launch of the UVN255P and SVN255P models reinforces this reputation. Designed primarily for commercial laundry applications, these units bring robust performance, efficiency, and advanced technology to heavy-duty environments.

At the core of the UVN255P and SVN255P models is their impressive washing capacity. With a significant load size capability, these machines are perfect for laundromats, hotels, and other high-demand facilities, enabling operators to process more laundry in less time. This capacity not only enhances productivity but also optimizes labor costs, allowing for greater operational efficiency.

One standout feature of both models is their user-friendly control interface. The intuitive controls are designed to simplify operation, minimizing the learning curve for new users. Alongside this, the machines offer programmable cycles that can be tailored to suit various fabrics and cleaning requirements. This flexibility ensures that the laundry process is not only efficient but also maintains the integrity of delicate items, as the right settings can be applied with ease.

Energy efficiency is another hallmark of the UVN255P and SVN255P. Both models are engineered to reduce water and energy consumption, aligning with sustainability goals that are increasingly important in today’s business environment. As a result, these machines not only contribute to a lower carbon footprint but also promise significant savings on utility bills, ultimately enhancing profitability for businesses.

Durability is also a key characteristic of these models, crafted with robust materials that withstand the rigors of constant use in commercial settings. The stainless steel construction not only ensures longevity but also makes maintenance simpler and quicker, minimizing downtime for facilities reliant on continued operation.

Furthermore, both models incorporate advanced technology features such as real-time performance monitoring and diagnostic tools. These capabilities allow operators to troubleshoot issues swiftly, reduce machine downtime, and maintain optimal performance levels.

In summary, the Alliance Laundry Systems UVN255P and SVN255P stand out in the commercial laundry market due to their high capacity, energy efficiency, user-friendly controls, and durable build. These features come together to provide businesses with a powerful solution that meets the demanding needs of modern laundry operations, ensuring that they can deliver high-quality service to their customers with confidence.