Kenmore 3405602 owner manual Exlernal ground, Connector, White neutral wire, Wire Connection with

Page 13

STEP 3. Attach a 3/4-inch, U.L.-listed, strain relief to the hole below terminal block opening. Strain relief should have a tight fit with dryer cabinet and be in a horizontal position. Put the power supply cord through the strain relief.

STEP 4. Loosen or remove terminal block screws. Connect the neutral wire (white

or center) of power supply cord under the center screw of the terminal block.

STEP 5. Connect the other two wires to outer terminal block screws. Tighten all terminal block screws firmly.

Exlernal ground

Centersilver-colored

connector

terminal blockscrew

White neutral wire

II. THREE-WIRE ELECTRICAL

CONNECTION (DIRECT WIRE) Prepare cable as directed:

Electrical Shock Hazard

Turn power supply off before connecting wires.

Use 10 gauge solid copper wire. Electrically ground dryer.

Failure to follow these instructions can result in death, fire, or electrical shock.

The dryer can be connected directly to fused disconnect or circuit breaker

box with three-wire,flexible armored or non-metallic sheathed copper cable (with grounding wire). All current-carrying wires must be insulated.

Neutral

 

grounding wire

3/4", U.L.-listed,

(green/yellow)

strain relief

3-Wire Connection with

Frame-Grounding Conductor

S'FEP6. Tighten the strain relief screws.

STEP 7. Insert tab of terminal block

cover into slot of the dryer rear panel. Secure cover with hold-down screw.

If local codes do not permit the connection of a frame-groundingconductor to the neutral wire, see

the instructions on page 15.

Otherwise, proceed with Exhaust Installation. See "CONNECT

E×HAUST" on page 19.

A conduit connector must be installed at junction box. Allow four feet of slack in the line so dryer can be moved if servicing

is ever necessary.

GROUNDING INSTRUCTIONS

This appliance must be connected to a grounded metal, permanent wiring

system; or an equipment-grounding conductor must be run with the circuit

conductors and connected to the equipment-groundingterminal or lead on the appliance.

STEP 1. Turn power supply off.

STEP la. Strip 31/2 inches of outer covering from end of cable. If using

3-wire cable with grounding wire, cut the bare wire even with outer covering.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A OwnersManual Installation InstructionsKeep this book and your Sears Full 1-YEAR Warranty on Mechanical and Electrical Parts Your safety and the safety of others is very importantYour Safety is Important to US Select Location Installation OverviewParts Needed If making a direct wire connection Tools Needed Parts Needed Optional depending Connect Exhaust pgs Tools Needed Parts NeededSelect Location for Your Dryer Standard InstallationProduct Dimensions Recessed AREA/CLOSET Installation InstructionsInstall Leveling Legs It is your responsibility If Your Home Has Wire electrical ReceptacleQuincy, Massachusetts Electrical Connection OptionsNEI THREE-WIREELECTRICALWhite neutral wire ConnectorWire Connection with Exlernal groundExhaust External Ground connector Conductor to the neutral wireAlternateconnection Four-wire receptacle Nema Type 14-30R III. Make FOUR-WIREElectrical Connection to Receptacle NeutralGreenwire WirePowersupply NeutralIV. FOUR-WIRE Electrical Connection Direct Wire BarecopperwireNeutral WhiteneutralwireRoute the Vent Typical installations for left or right side exhaustingExhaust Hood Type Determine Vent LengthStep IDryer Flexible metalventDucttape & clamp Loop System Offset Connections with Close ClearancesPeriscope System Final Steps Review InstallationSTOPPING/RESTARTING Starting Your DryerYour Dryer Auto DRY Cycle Cycle DescriptionTimed DRY Cycle Touch UP CycleCottons and Linens FABRIC/TEMPERATURE ControlTo use AIR Fluff Using AIR DRY/AIR FluffAIR Fluff Delicate FabricsCool Down Push to Start ButtonWrinkleguard Using Wrinkle GuardLint Alert HEATEDDR.RACK Choosing Load Sizes Preparing Clothes For DryingSuper Capacity Plus Dryers Drying Tips Using Dryer FABRICSOFrENERSExterior Cleaning Your DryerInterior To clean Cleaning the Lint ScreenWash Lint Screen As Needed To washTo remove accumulated lint from Inside the dryer Checking for AIR Flow ObstructionRemoving Accumulated Lint Moving Care Changing the Drum LightVacation Care Not Drying Load is overdried ContStains on Load WrinkledSears Maintenance Agreement We Service What We SellKenmore Dryers For more information, callPage 8F,eLR8
Top Page Image Contents