Kenmore 3405602 owner manual Wire, Neutral, Greenwire, Green/yellow, Powersupply

Page 17

STEP 3. Attach a 3/4-inch, U.L.-listed, strain relief to the hole below terminal block opening. Strain relief should have a tight fit with dryer cabinet and be in a horizontal position. Put the power supply cord through the strain relief.

STEP 4. Remove the center terminal block screw. Remove the neutral ground- ing wire (green/yellow wire) from extemal grounding screw.

STEP 5. Connect neutral grounding wire and the neutral wire (white) of power

supply cord under the center screw of terminal block.

STEP 6. Connect the other two insulated wires to outer terminal block screws.

STEP 7. Connect the green, grounding wire from the power supply cord to the external grounding conductor screw.

Tighten all terminal block screws firmly.

ExternalgroundCentersilver-colored

connectorterminalblockscrew

Green/yellowwire of harness

STEP 8. Tighten the strain relief screws.

STEP 9. Insert tab of terminal block cover into slot of the dryer rear panel. Secure cover with hold-down screw.

Proceed with Exhaust Installation. See "CONNECT EXHAUST" on

page 19.

	Centersilver-
External	coloredterminal
External	:k screw
ground
connector	White neutral
	wire

		Neutral
	Greenwire	groundingwire
	Greenwire	(green/yellow)
	of powersupply	(green/yellow)
	of powersupply
	cordor bare
	copperwire
	/,, U.L.-listed,
	3	l!
	strainrelief
	4-WireConnection	with

Frame-Grounding Conductor

17

Image 17

Contents Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A OwnersManual Installation InstructionsKeep this book and your Sears Full 1-YEAR Warranty on Mechanical and Electrical Parts Your safety and the safety of others is very importantYour Safety is Important to US Parts Needed Installation OverviewSelect Location If making a direct wire connection Tools Needed Parts Needed Optional depending Connect Exhaust pgs Tools Needed Parts NeededSelect Location for Your Dryer Standard InstallationProduct Dimensions Recessed AREA/CLOSET Installation InstructionsInstall Leveling Legs It is your responsibility If Your Home Has Wire electrical ReceptacleQuincy, Massachusetts Electrical Connection OptionsNEI THREE-WIREELECTRICALWhite neutral wire ConnectorWire Connection with Exlernal groundExhaust Alternateconnection Conductor to the neutral wireExternal Ground connector Four-wire receptacle Nema Type 14-30R III. Make FOUR-WIREElectrical Connection to Receptacle NeutralGreenwire WirePowersupply NeutralIV. FOUR-WIRE Electrical Connection Direct Wire BarecopperwireNeutral WhiteneutralwireRoute the Vent Typical installations for left or right side exhaustingStep Determine Vent LengthExhaust Hood Type Ducttape & clamp Flexible metalventIDryer Periscope System Offset Connections with Close ClearancesLoop System Final Steps Review InstallationYour Dryer Starting Your DryerSTOPPING/RESTARTING Auto DRY Cycle Cycle DescriptionTimed DRY Cycle Touch UP CycleCottons and Linens FABRIC/TEMPERATURE ControlTo use AIR Fluff Using AIR DRY/AIR FluffAIR Fluff Delicate FabricsCool Down Push to Start ButtonLint Alert Using Wrinkle GuardWrinkleguard HEATEDDR.RACK Super Capacity Plus Dryers Preparing Clothes For DryingChoosing Load Sizes Drying Tips Using Dryer FABRICSOFrENERSInterior Cleaning Your DryerExterior To clean Cleaning the Lint ScreenWash Lint Screen As Needed To washRemoving Accumulated Lint Checking for AIR Flow ObstructionTo remove accumulated lint from Inside the dryer Vacation Care Changing the Drum LightMoving Care Not Drying Load is overdried ContStains on Load WrinkledSears Maintenance Agreement We Service What We SellKenmore Dryers For more information, callPage 8F,eLR8