Kenmore 3405602 owner manual Changing the Drum Light, Moving Care, Vacation Care

Page 37

CHANGING THE DRUM LIGHT

The dryer light automatically turns on inside the dryer drum when you open the door.

To replace bulb:

STEP 1. Unplug power supply cord or turn off electrical power supply.

STEP 2. Open the dryer door. Remove the screw that holds the lens in place.

STEP 3. Remove the lens by pulling it down and away from drum.

STEP 4. Push tab to allow bulb to

swing out.

STEP 5. Check that the light bulb is screwed in tightly. The vibration of the dryer may cause the bulb to come loose. If this is not the problem, remove the light bulb by turning it counterclockwise.

IMPORTANT: Replace the bulb with a 25-watt, 120V A.C. bulb only.

STEP 6. Install light bulb by turning it clockwise.

STEP 7, Push bottom of light and socket assembly in until tab locks.

STEP 8. Place the top of the lens onto the top of the holder. Rotate the bottom of the lens down until it is in place.

Replace screw. NOTE: It is very impor- tant that the lens is replaced properly.

STEP 9. Plug in power supply cord or turn on electric supply.

MOVING CARE

•Unplug power supply cord or turn off electrical power supply.

•Make sure leveling legs are secure in dryer base.

•Use masking tape to secure dryer door.

VACATION CARE

•Unplug power supply cord or turn off electrical power supply.

•Wash lint screen.

37

Image 37

Contents Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A OwnersManual Installation InstructionsKeep this book and your Sears Full 1-YEAR Warranty on Mechanical and Electrical Parts Your safety and the safety of others is very importantYour Safety is Important to US Select Location Installation OverviewParts Needed If making a direct wire connection Tools Needed Parts Needed Optional depending Connect Exhaust pgs Tools Needed Parts NeededSelect Location for Your Dryer Standard InstallationProduct Dimensions Recessed AREA/CLOSET Installation InstructionsInstall Leveling Legs It is your responsibility If Your Home Has Wire electrical ReceptacleQuincy, Massachusetts Electrical Connection OptionsNEI THREE-WIREELECTRICALWhite neutral wire ConnectorWire Connection with Exlernal groundExhaust External Ground connector Conductor to the neutral wireAlternateconnection Four-wire receptacle Nema Type 14-30R III. Make FOUR-WIREElectrical Connection to Receptacle NeutralGreenwire WirePowersupply NeutralIV. FOUR-WIRE Electrical Connection Direct Wire BarecopperwireNeutral WhiteneutralwireRoute the Vent Typical installations for left or right side exhaustingExhaust Hood Type Determine Vent LengthStep IDryer Flexible metalventDucttape & clamp Loop System Offset Connections with Close ClearancesPeriscope System Final Steps Review InstallationSTOPPING/RESTARTING Starting Your DryerYour Dryer Auto DRY Cycle Cycle DescriptionTimed DRY Cycle Touch UP CycleCottons and Linens FABRIC/TEMPERATURE ControlTo use AIR Fluff Using AIR DRY/AIR FluffAIR Fluff Delicate FabricsCool Down Push to Start ButtonWrinkleguard Using Wrinkle GuardLint Alert HEATEDDR.RACK Choosing Load Sizes Preparing Clothes For DryingSuper Capacity Plus Dryers Drying Tips Using Dryer FABRICSOFrENERSExterior Cleaning Your DryerInterior To clean Cleaning the Lint ScreenWash Lint Screen As Needed To washTo remove accumulated lint from Inside the dryer Checking for AIR Flow ObstructionRemoving Accumulated Lint Moving Care Changing the Drum LightVacation Care Not Drying Load is overdried ContStains on Load WrinkledSears Maintenance Agreement We Service What We SellKenmore Dryers For more information, callPage 8F,eLR8