ADC AD-115ES installation manual Basket Tumbler Coating

Page 37

b.Steam Models

Check to ensure that the steam damper is functioning properly. The steam damper should not “slam” (open or closed) when it reaches the end of (piston) travel. Additionally, the steam damper should not bind and/or stop during travel. If either of these conditions occur, the flow control must be adjusted. Refer to the illustration on page 28 for air adjustment instructions.

6.Make a complete operational check of ALL safety-related circuits (i.e., lint drawer switch and sail switch on gas models).

NOTE: To check for proper sail switch operation, open the main door and while holding main door switch plunger in, start the dryer. The dryer should start, but the heat circuit should not be activated (on). If the heat (burner) does activate, shut the dryer off and make the necessary adjustments.

7.Reversing basket (tumbler) dryers should never be operated with less than a 76 lb (34.5 kg) load (dry weight), since the load’s weight affects basket (tumbler) coast time during a direction reversal command. It is important that the basket (tumbler) come to a complete stop prior to starting in opposite direction.

Microprocessor Controller (Computer) Dryer Models

a.Spin and dwell (stop) times are not adjustable in the Automatic Mode and have been preprogrammed into the microprocessor controller (computer) for 150-seconds spin time in the forward direction and 120-seconds in the reverse direction with a 5-second dwell (stop) time.

b.Spin and dwell (stop) times are adjustable in the Manual (Timed) Mode.

BASKET (TUMBLER) COATING

The basket (tumbler) is treated with a protective coating. We suggest dampening old garments or cloth material with a solution of water and nonflammable mild detergent and tumbling them in the basket (tumbler) to remove this coating.

8.Each dryer should be operated through one (1) complete cycle to ensure that no further adjustments are necessary and that ALL components are functioning properly.

9.Make a complete operational check of ALL operating controls.

a.Microprocessor controller (computer) programs and selections

Each microprocessor controller (computer) has been preprogrammed by the factory with the most commonly used parameter (program) selections. If computer program changes are required, refer to the computer programming manual, which was shipped with the dryer.

b.Dual timer dryers check

1)Heating Timer

2)Cool Down Timer

3)Temperature Selection Switch

113202 - 10

www.amdry.com

33

Page 36 Page 38
Image 37
Page 36 Page 38
Contents AD-115ES Installation Manual Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Section Safety PrecautionsStandard Specifications SPECIFICATIONS/COMPONENT IdentificationSpecifications Gas, Electric, and Steam Component Identification 113202 Location Requirements Installation ProceduresUnpacking and Setting UP American Dryer Corp 113202 This Exhaust Duct Transition Piece Must be Installed First Fresh AIR Supply Requirements Dryer Enclosure RequirementsGeneral Exhaust Ductwork Information Exhaust RequirementsAmerican Dryer Corp 113202 Outside Ductwork Protection American Dryer Corp 113202 Electrical Information Reversing, 3ø Motor Gas and Steam Reversing, 3ø Motor Electric American Dryer Corp 113202 GAS Information Type of GAS Type of GAS American Dryer Corp 113202 Steam Information Operating Steam PressureCompressed Air Supply Air Pressure Steam Damper System113202 Before YOU Start Check Local Codes and Permits Water Information113202 Typical Water Supply Preparation for Operation and START-UP Preoperational Test Basket Tumbler Coating Preoperational Instructions Dual Timer DryersShutdown Instructions Reversing Timer SPIN/DWELL AdjustmentsService SERVICE/PARTS InformationParts Returning Warranty Cards Warranty InformationWarranty Returning Warranty PartsAmerican Dryer Corp 113202 Cleaning Routine MaintenanceSuggested Cleaning Schedule Lubrication AdjustmentsData Label Information Procedure for Functional Check Replacement Components 113202 Phase Manual Reset Burner HI-LIMIT InstructionsDual Timer 113202 ADC Part No 10 12/10/08
Top Page Image Contents