Maytag W10097016A-SP Vacation, storage, and moving care, Moving Care, Reinstalling the Dryer

Page 10

Vacation, storage, and moving care

Install and store your dryer where it will not freeze. Because some water may stay in the hoses, freezing can damage your dryer. If storing or moving your dryer during freezing weather, winterize it.

Non-Use or Storage Care

Operate your dryer only when you are at home. If you will be on vacation or not using your dryer for an extended period of time, you should:

1.Unplug dryer or disconnect power.

2.Clean lint screen. See “Cleaning the Lint Screen.”

Moving Care

For power supply cord-connected dryers:

1.Unplug the power supply cord.

2.Steam models only: Shut off water faucet.

3.Steam models only: Disconnect the water inlet hose from faucet, then drain the hose. Remove the hose from the back of the dryer. Transport hose separately.

4.Make sure leveling legs are secure in dryer base.

5.Use tape to secure dryer door.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

For direct-wired dryers:

1.Turn off power at fuse or breaker box.

2.Disconnect wiring.

3.Steam models only: Shut off water faucet.

4.Steam models only: Disconnect the water inlet hose from faucet, then drain the hose. Transport hose separately.

5.Make sure leveling legs are secure in dryer base.

6.Use tape to secure dryer door.

Reinstalling the Dryer

Follow the “Installation Instructions” to locate, level, and connect the dryer.

Changing the Sensor Cycle Settings to Increase Drying Time

If all your loads on all Sensor cycles are consistently not as dry as you would like, you may change the default settings to increase the default dryness level.

Your sensor drying settings can be adjusted to adapt to different installations, environmental conditions, or personal preference. This change is retained and will affect all of your Sensor cycles, not just the current cycle/load. There are 3 drying settings, which are displayed using the “Status” lights (Wet, Damp, Cool Down)

1Factory preset dryness level.

2Slightly drier clothes, 15% more drying time.

3Much drier clothes, 30% more drying time.

To change the drying settings:

NOTE: The settings cannot be changed while the dryer is running or paused. The dryer must be in standby mode (the power button is off) to adjust the default settings.

1.Before starting a cycle, press and hold the TEMP LEVEL button for 6 seconds.

2.Press the TEMP LEVEL button to select the dryness level shown in the LED display: Wet light on = level 1, Wet and Damp lights on = level 2, and Wet, Damp, and Cool Down lights on = level 3.

3.Press START/PAUSE to save the new dryness level setting.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Guide D’UTILISATION ET Dryer Safety Your safety and the safety of others are very importantWhat to do if YOU Smell GAS Maintain good air flow by Check Your Vent System for Good AIR FlowGood air flow Use Sensor Cycles for better fabric care and energy savingsControl Panel & Features Cycle Guide Timed DRY Cycles Setting the Drying TemperatureCycle Guide Sensor DRY Cycles Items to dry Cycle Drying Available Cycle DetailsClean the lint screen Load the dryer Using Your DryerPress POWER/CANCEL Select the desired cycle Select cycle options if desired Setting modifiersWrinkle Prevent feature Press START/PAUSE to begin cycleCleaning the lint screen Cleaning the dryer locationCleaning the dryer interior Dryer CareVacation, storage, and moving care Reinstalling the DryerChanging the Sensor Cycle Settings to Increase Drying Time Moving CareTroubleshooting If you experience Possible Causes SolutionTroubleshooting Maytag Laundry Warranty This limited warranty does not coverSécurité DE LA Sécheuse Votre sécurité et celle des autres est très importanteImportantes Instructions DE Sécurité Circulation d’air adéquate Nettoyer le filtre à charpie avant chaque chargeBouton START/PAUSE mise en marche/pause Tableau DE Commande ET CaractéristiquesSignal de fin Caractéristique Wrinkle PreventRéglage de la température de séchage Guide DE Programmes Programmes DE Détection D’HUMIDITÉGuide DE Programmes Programmes DE Séchage Minuté Programme Température Options Détails du programmeUtilisation DE LA Sécheuse Appuyer sur POWER/CANCEL mise sous tension/annulationNettoyer le filtre à charpie Charger la sécheuse Niveau de température Sélectionner les modificateursCaractéristique Wrinkle Prevent Nettoyage de l’intérieur de la sécheuse Nettoyer l’emplacement de la sécheuseEntretien DE LA Sécheuse Retirer la charpie accumuléePrécautions à prendre avant un déménagement Réinstallation de la sécheuseChangement de la lampe du tambour sur certain modèles Pour modifier les réglages de séchageDépannage Dépannage Garantie DES Appareils DE Buanderie Maytag La présente garantie limitée ne couvre pasPage Page Si vous avez besoin de pièces de rechange If you need replacement parts or to order accessoriesOur consultants provide assistance with Nos consultants fournissent ’assistance pour
Top Page Image Contents