Humminbird HDR 650 manual Specifications

Page 46

Specifications

Depth Capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .600 ft (180 m) Power Cable Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36" (91 cm) Operating Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200 kHz Area of Coverage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20° @ -10 dB Power Output . . . . . . . . . . . . .250 Watts (RMS), 2000 Watts (Peak to Peak) Current Draw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 mA Power Requirement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 - 20 VDC Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Liquid Crystal Diode (LCD) Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .In-Dash 2 1/8" hole Unit Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .High-Impact Plastic Transducer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .XNT 9 20 Transducer Cable Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 ft (6 m)

IPX Rating . . . . . . . . . . . . . . . . . . .IP67 Waterproof/Submersible @ 1 m for 30 minutes and dust tight

NOTE: Humminbird® verifies maximum stated depth in saltwater conditions, but actual depth performance may vary due to transducer installation, water type, thermal layers, bottom composition and slope.

NOTE: Product specifications and features are subject to change without notice.

Specifications

42

Image 46
Contents HDR 650 Installation Operations Manual Thank You Table of Contents Maintenance How Sonar Works Installation Overview Installing the HDR Locating the HDR 650 Mounting Position Cutting the Mounting HoleCustomizing and Assembling the HDR HDR Face Plate Trim Ring TabsCollar Gasket DashboardView Installing the HDRHDR 650 Control Head Connecting to the Power Supply Installing the BuzzerBuzzer Installing the Transducer Inline Fuse HolderTransducer Installation Overview Rivets Strakes TransomHull Transom Transducer InstallationLocating the Transducer Mounting Position StepRibLevel Deadrise AnglePreparing the Mounting Location 4th hole Mark Initial Assembling the Transducer and Initial MountingDrill Holes Transom Angle in degrees MeasuredWeight Distance Bead Alignment Number Transom Angle Measured DistanceRib Knuckle Beads RatchetBead Ratchet Snap the pivot arm down into place One click too high Trailingedge One click too low Leading edgeRouting the Cable Transom Mount Transducer Installation Storing Excess Cable Gathered at one location as shown Connecting the CableTest and Finish the Installation See the illustration Storing Excess CableLevel Seam aligned with boat hull Bead Rib RatchetTransom Mount Transducer Installation Locking Down the Transducer Optional Inside the Hull Transducer Installation Trial Installation Positioning the Transducer and Preferred Mounting AreaRouting the Cable Permanently Mounting the Transducer Make sure the position of the transducer is markedTrolling Motor Transducer Installation Trolling Motor Transducer OptionsHDR 650 Control Head Units Shallow Alarm Icon IndicatesOperating the HDR DepthPower On/Off Key Functions OverviewUnits Set UnitsShallow Alarm Set Shallow Alarm IconDeep Alarm Set Deep Alarm IconNegativeOffset NumberIcon PostiveOffset NumberIconHDR 650 Maintenance MaintenanceTransducer Maintenance Troubleshooting HDR 650 Doesnt Power UpScreen Fades, Images are not Sharp No Bottom Reading on the DisplayNo Continuous Depth Display in Very Shallow Water Bottom Reading Disappears During a Hard TurnYear Limited Warranty Humminbird Service Policy Returning Your Unit for Service Specifications Specifications Contact Humminbird