Furuno NAVpilot-500 manual Data available for display in Screen 2 Upper and Lower, Displayed data

Page 14

 

2. BASIC OPERATION

Data available for display in SCREEN 2 UPPER and LOWER

Menu option

Displayed data

 

 

POS

Own ship’s position (L/L)

 

 

COG

Course over ground

 

 

SOG

Speed over ground

 

 

STW

Speed through water

 

 

TMP

Water temperature

 

 

DPT

Depth

 

 

BRG

Bearing to waypoint

 

 

RNG

Range to waypoint

 

 

WPT POS

Waypoint position (L/L)

 

 

XTE

Cross-track error

 

 

TTG

Time-to-Go to Destination

 

 

ETA

Estimated Time of Arrival

 

 

DATE

Date

 

 

TIME

Time

 

 

WIND T*

Wind direction and speed (True)

 

 

WIND R**

Wind direction and speed (Relative)

 

 

VOLT

Input/output power voltage to the processor unit

 

 

TRIP

Trip distance

 

 

*True:

The speed and direction (in relation to ship’s bow) of the wind felt

 

or measured when stationary.

**Relative:

The direction (in relation to ship’s bow) and speed of the wind as it

 

appears to those on board, relative to the speed and direction of

 

the boat; combination of the true wind and the wind caused by the

 

boat’s movement.

6.Press the [ENTER] knob.

7.Press the [MENU] key to close the menu.

2-5

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Autopilot Safety Instructions Table of Contents Alarms IiiWord to the Owner of the NAVpilot-500 FeaturesForeword System Configuration System configuration of NAVpilot-500This page is intentionally left blank Principle of the Autopilot Principle of AutopilotPrinciple of Operation Control unit, front view Basic OperationOperating Controls Startup sequence Turning the power offTurning On/Off Contrast, brilliance window Adjusting Brilliance and ContrastDisplays DisplaysSelecting data for Normal Display 2 screen Screen setup menuSelecting the data shown on Normal and Data Displays Normal DisplayData available for display in Screen 2 Upper and Lower Displayed dataScreen 3 pattern options window Selecting the display layout for Data DisplayData Displays Selecting data for Data DisplayGraphic displays Selecting the display on Graphic DisplayGraphic options window Normal Display 1 Selecting data for analog indicatorDisplay setup menu Analog indicator bar options window Rudder AngleThis page is intentionally left blank Steering Modes Stby ModeStby mode display Auto mode display Auto ModeUsing the Auto mode Enabling the Advanced Auto mode Advanced Auto modeAdvanced Auto mode display Advanced auto options windowTurn Turn mode For Auto modeTurn setting window NAV mode display NAV ModeStarting the NAV mode NAV mode, Course and XTE Selecting sailing method of NAV modeNav mode options window NAV mode menu Switching waypointWaypoint switching options window Fishing mode options window OFFOrbit mode Do not use the Orbit mode in rough seaClover Leaf Navigating to TLL point Fishing modeFishing mode window OrbitRemote Mode Dial type remote controller FAP-5551Turning power off dial type Rotating dialTurning power on, button and lever type remote controllers NFU No Follow-Up mode displayOperating remote controller ex. button and lever types Turning power off, button and lever type remote controllersSystem setup menu Selecting course after the Remote mode is offStby mode menu Course after remote controller is turned off Cse course after remote options windowDodge mode display Dodge ModeDodging in Stby mode Dodging in Auto or NAV mode Menu Operation Stby Mode MenuOffsetting data Data calibration menuSelecting the selecting method of magnetic variation Offsetting the heading dataShip’s speed, temperature, depth calibration Magnetic variation options windowSelecting the method of entering the parameter Setting parametersParameter setup menu Sea state options windowMANUAL-CALM Deviation level options windowSetting parameters manually Example of Manual parameterWeather Track line and weather setting valueRudder angle and rudder gain setting Rudder GainCounter Rudder General guidelines for setting rudder gainGeneral guidelines for setting counter rudder gain Adjusting the sensitivity in monitoring the boat’s trim Auto trim options windowWhen towing the net Auto net towing options windowSetting the units of measurements Speed unit options window, for exampleDDMM.MM’ Key beep options window Setting other menu itemsActivating key beep Lock options window Setting the panel dimmerLocking the control unit Selecting languageSimulation mode options window Running simulation programAlarm menu AlarmsAlarm Menu Alarm interval options window Selecting the alarm buzzerAudio alarm options window Selecting the beep patternSetting the cross-track error limit Setting the watch alarmSetting the heading deviation alarm Watch alarm options windowApplication of XTE alarm Setting the speed alarmHow to use XTE alarm Into mode Speed alarm options windowSetting the depth alarm Depth alarm options windowTemp alarm options window Setting the temperature alarmSetting the trip distance alarm Log trip options windowLog trip clear options window Alarm InformationClearing the trip distance Alarm messages Alarm messages, their meanings and prioritiesMaintenance program Maintenance & TroubleshootingPreventive Maintenance Check point RemedyParts Name Type Code No Remarks Replacement of FuseDiagnostics Test options windowHeading Sensor Test Processor Unit TestController Unit Test Keyboard Test Screen TestRudder Setup and Auto Test Rudder testSystem data screen Clearing MemoriesSystem Data Memory clear options windowError message Meaning Remedy Error MessagesError messages Error messages con’t Menu Tree MN-1Stby mode menu MN-2Auto mode menu MN-3Processor Unit NAVpilot-500Control Unit InterfaceColor Power SupplyEnvironmental Conditions Index IN-1
Related manuals
Manual 73 pages 25.32 Kb

NAVpilot-500 specifications

The Furuno NAVpilot-500 is an advanced autopilot system designed for a range of vessels, from small boats to larger commercial ships. This cutting-edge technology provides reliable steering assistance, ensuring enhanced navigational safety and improved operational efficiency. With its versatile functionalities, the NAVpilot-500 has made a significant impact in the maritime industry.

One of the standout features of the Furuno NAVpilot-500 is its use of FURUNO's proprietary technology, including advanced sensors and algorithms. This system leverages a dual-processor architecture, allowing for seamless performance in diverse sea conditions. The NAVpilot-500 is capable of handling course control with impressive precision, adjusting automatically to wind and waves to maintain a steady course.

Another notable aspect of this autopilot system is the intuitive user interface. The large, sunlight-readable display provides easy access to all functionalities and settings, making it user-friendly for operators of varying expertise levels. The touchscreen interface allows for straightforward navigation through menus, ensuring that users can quickly adapt to changing conditions on the water.

The NAVpilot-500 features a comprehensive set of integration options, including compatibility with various types of navigation and communication equipment. This capability allows for effective integration with Furuno's proprietary chart plotters and radar systems, ultimately enhancing situational awareness and safety while navigating.

Moreover, the system offers customizable autopilot modes, including modes for auto and standby operation. This versatility allows users to choose the most suitable steering method for their specific needs, whether for leisurely cruising or during heavy-duty fishing operations. The NAVpilot-500 also incorporates advanced safety features, such as target tracking and collision avoidance, ensuring that operators remain vigilant and prepared for any potential hazards.

Furuno's NAVpilot-500 is engineered for durability and reliability, meeting the rigorous standards set by the maritime industry. Robust construction allows it to withstand harsh marine environments, providing peace of mind to operators. With its blend of advanced technology, user-friendly design, and reliable performance, the NAVpilot-500 stands out as one of the leading autopilot systems in the market today. Whether for leisure or professional use, this system brings a level of sophistication and safety that enhances navigation experiences across various maritime applications.
Top Page Image Contents