Furuno NAVpilot-500 manual This page is intentionally left blank

Page 19

2. BASIC OPERATION

This page is intentionally left blank.

2-10

Image 19

Contents Autopilot Safety Instructions Table of Contents Iii AlarmsForeword FeaturesWord to the Owner of the NAVpilot-500 System configuration of NAVpilot-500 System ConfigurationThis page is intentionally left blank Principle of Autopilot Principle of the AutopilotPrinciple of Operation Operating Controls Basic OperationControl unit, front view Turning On/Off Turning the power offStartup sequence Displays Adjusting Brilliance and ContrastDisplays Contrast, brilliance windowNormal Display Screen setup menuSelecting the data shown on Normal and Data Displays Selecting data for Normal Display 2 screenDisplayed data Data available for display in Screen 2 Upper and LowerSelecting data for Data Display Selecting the display layout for Data DisplayData Displays Screen 3 pattern options window Graphic options window Selecting the display on Graphic Display Graphic displays Display setup menu Selecting data for analog indicatorNormal Display 1 Rudder Angle Analog indicator bar options windowThis page is intentionally left blank Stby mode display Stby ModeSteering Modes Using the Auto mode Auto ModeAuto mode display Advanced auto options window Advanced Auto modeAdvanced Auto mode display Enabling the Advanced Auto modeTurn setting window Turn mode For Auto modeTurn Starting the NAV mode NAV ModeNAV mode display Nav mode options window Selecting sailing method of NAV modeNAV mode, Course and XTE Waypoint switching options window Switching waypointNAV mode menu OFF Fishing mode options windowDo not use the Orbit mode in rough sea Orbit modeOrbit Navigating to TLL point Fishing modeFishing mode window Clover LeafDial type remote controller FAP-5551 Remote ModeRotating dial Turning power off dial typeNFU No Follow-Up mode display Turning power on, button and lever type remote controllersTurning power off, button and lever type remote controllers Operating remote controller ex. button and lever typesStby mode menu Selecting course after the Remote mode is offSystem setup menu Cse course after remote options window Course after remote controller is turned offDodging in Stby mode Dodge ModeDodge mode display Dodging in Auto or NAV mode Data calibration menu Stby Mode MenuOffsetting data Menu OperationMagnetic variation options window Offsetting the heading dataShip’s speed, temperature, depth calibration Selecting the selecting method of magnetic variationSea state options window Setting parametersParameter setup menu Selecting the method of entering the parameterDeviation level options window MANUAL-CALMExample of Manual parameter Setting parameters manuallyRudder Gain Track line and weather setting valueRudder angle and rudder gain setting WeatherGeneral guidelines for setting counter rudder gain General guidelines for setting rudder gainCounter Rudder Auto trim options window Adjusting the sensitivity in monitoring the boat’s trimAuto net towing options window When towing the netSpeed unit options window, for example Setting the units of measurementsDDMM.MM’ Activating key beep Setting other menu itemsKey beep options window Selecting language Setting the panel dimmerLocking the control unit Lock options windowRunning simulation program Simulation mode options windowAlarm Menu AlarmsAlarm menu Selecting the beep pattern Selecting the alarm buzzerAudio alarm options window Alarm interval options windowWatch alarm options window Setting the watch alarmSetting the heading deviation alarm Setting the cross-track error limitSpeed alarm options window Setting the speed alarmHow to use XTE alarm Into mode Application of XTE alarmDepth alarm options window Setting the depth alarmLog trip options window Setting the temperature alarmSetting the trip distance alarm Temp alarm options windowClearing the trip distance Alarm InformationLog trip clear options window Alarm messages, their meanings and priorities Alarm messagesCheck point Remedy Maintenance & TroubleshootingPreventive Maintenance Maintenance programTest options window Replacement of FuseDiagnostics Parts Name Type Code No RemarksController Unit Test Processor Unit TestHeading Sensor Test Screen Test Keyboard TestRudder test Rudder Setup and Auto TestMemory clear options window Clearing MemoriesSystem Data System data screenError messages Error MessagesError message Meaning Remedy Error messages con’t MN-1 Menu TreeMN-2 Stby mode menuMN-3 Auto mode menuInterface NAVpilot-500Control Unit Processor UnitEnvironmental Conditions Power SupplyColor IN-1 Index

Related manuals

Manual 73 pages 25.32 Kb