Furuno NAVpilot-500 manual Setting parameters, Parameter setup menu, Sea state options window

Page 40

4. MENU OPERATION

4.1.2 Setting parameters

The PARAMETER SETUP menu sets various parameters for the control of the NAVpilot-500.

1.On the STBY mode, press the [MENU] key to open the STBY mode menu.

2.Rotate the [ENTER] knob to select “PARAMETER SETUP”.

3.Press the [ENTER] knob to show the PARAMETER SETUP menu.

SEA STATE: FULL-AUTO

DEVIATION LEVEL:

AUTO

MANUAL PARAMETER

 

AUTO TRIM:

OFF

ADVANCED AUTO:

NO

NET TOWING AUTO:

NO

NAV MODE:

XTE

RADIUS OF ORBIT:

1.00 nm

FISHING MODE:

OFF

WAYPOINT SWITCHING:

AUTO

Parameter setup menu

4. To close the PARAMETER SETUP menu, press the [MENU] key.

Selecting the method of entering the parameter

The NAVpilot-500 has an automatic adjustment feature which sets up the equipment according to ship’s characteristics and sea state for optimum performance in the AUTO and NAV modes. Further, a self-learning algorithm is incorporated: Parameters for rudder ratio, counter rudder and auto trim gains, input at the sea trial after the installation and experiences of your boat, are stored in memory for navigation in the future.

Note that the default settings for FULL-AUTO have been detected based on the BOAT TYPE and BOAT LENGTH on installing.

You may set sea state as follows:

1.Rotate the [ENTER] knob to select “SEA STATE” from the PARAMETER SETUP menu.

2.Press the [ENTER] knob to show the sea state options window.

FULL-AUTO

SEMI-AUTO

MANUAL-CALM

MANUAL-MODERATE

MANUAL-ROUGH

Sea state options window

4-3

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Autopilot Safety Instructions Table of Contents Alarms IiiForeword FeaturesWord to the Owner of the NAVpilot-500 System Configuration System configuration of NAVpilot-500This page is intentionally left blank Principle of the Autopilot Principle of AutopilotPrinciple of Operation Operating Controls Basic OperationControl unit, front view Turning On/Off Turning the power offStartup sequence Adjusting Brilliance and Contrast DisplaysContrast, brilliance window DisplaysScreen setup menu Selecting the data shown on Normal and Data DisplaysSelecting data for Normal Display 2 screen Normal DisplayData available for display in Screen 2 Upper and Lower Displayed dataSelecting the display layout for Data Display Data DisplaysScreen 3 pattern options window Selecting data for Data DisplayGraphic options window Selecting the display on Graphic DisplayGraphic displays Display setup menu Selecting data for analog indicatorNormal Display 1 Analog indicator bar options window Rudder AngleThis page is intentionally left blank Stby mode display Stby ModeSteering Modes Using the Auto mode Auto ModeAuto mode display Advanced Auto mode Advanced Auto mode displayEnabling the Advanced Auto mode Advanced auto options windowTurn setting window Turn mode For Auto modeTurn Starting the NAV mode NAV ModeNAV mode display Nav mode options window Selecting sailing method of NAV modeNAV mode, Course and XTE Waypoint switching options window Switching waypointNAV mode menu Fishing mode options window OFFOrbit mode Do not use the Orbit mode in rough seaNavigating to TLL point Fishing mode Fishing mode windowClover Leaf OrbitRemote Mode Dial type remote controller FAP-5551Turning power off dial type Rotating dialTurning power on, button and lever type remote controllers NFU No Follow-Up mode displayOperating remote controller ex. button and lever types Turning power off, button and lever type remote controllersStby mode menu Selecting course after the Remote mode is offSystem setup menu Course after remote controller is turned off Cse course after remote options windowDodging in Stby mode Dodge ModeDodge mode display Dodging in Auto or NAV mode Stby Mode Menu Offsetting dataMenu Operation Data calibration menuOffsetting the heading data Ship’s speed, temperature, depth calibrationSelecting the selecting method of magnetic variation Magnetic variation options windowSetting parameters Parameter setup menuSelecting the method of entering the parameter Sea state options windowMANUAL-CALM Deviation level options windowSetting parameters manually Example of Manual parameterTrack line and weather setting value Rudder angle and rudder gain settingWeather Rudder GainGeneral guidelines for setting counter rudder gain General guidelines for setting rudder gainCounter Rudder Adjusting the sensitivity in monitoring the boat’s trim Auto trim options windowWhen towing the net Auto net towing options windowSetting the units of measurements Speed unit options window, for exampleDDMM.MM’ Activating key beep Setting other menu itemsKey beep options window Setting the panel dimmer Locking the control unitLock options window Selecting languageSimulation mode options window Running simulation programAlarm Menu AlarmsAlarm menu Selecting the alarm buzzer Audio alarm options windowAlarm interval options window Selecting the beep patternSetting the watch alarm Setting the heading deviation alarmSetting the cross-track error limit Watch alarm options windowSetting the speed alarm How to use XTE alarm Into modeApplication of XTE alarm Speed alarm options windowSetting the depth alarm Depth alarm options windowSetting the temperature alarm Setting the trip distance alarmTemp alarm options window Log trip options windowClearing the trip distance Alarm InformationLog trip clear options window Alarm messages Alarm messages, their meanings and prioritiesMaintenance & Troubleshooting Preventive MaintenanceMaintenance program Check point RemedyReplacement of Fuse DiagnosticsParts Name Type Code No Remarks Test options windowController Unit Test Processor Unit TestHeading Sensor Test Keyboard Test Screen TestRudder Setup and Auto Test Rudder testClearing Memories System DataSystem data screen Memory clear options windowError messages Error MessagesError message Meaning Remedy Error messages con’t Menu Tree MN-1Stby mode menu MN-2Auto mode menu MN-3NAVpilot-500 Control UnitProcessor Unit InterfaceEnvironmental Conditions Power SupplyColor Index IN-1
Related manuals
Manual 73 pages 25.32 Kb

NAVpilot-500 specifications

The Furuno NAVpilot-500 is an advanced autopilot system designed for a range of vessels, from small boats to larger commercial ships. This cutting-edge technology provides reliable steering assistance, ensuring enhanced navigational safety and improved operational efficiency. With its versatile functionalities, the NAVpilot-500 has made a significant impact in the maritime industry.

One of the standout features of the Furuno NAVpilot-500 is its use of FURUNO's proprietary technology, including advanced sensors and algorithms. This system leverages a dual-processor architecture, allowing for seamless performance in diverse sea conditions. The NAVpilot-500 is capable of handling course control with impressive precision, adjusting automatically to wind and waves to maintain a steady course.

Another notable aspect of this autopilot system is the intuitive user interface. The large, sunlight-readable display provides easy access to all functionalities and settings, making it user-friendly for operators of varying expertise levels. The touchscreen interface allows for straightforward navigation through menus, ensuring that users can quickly adapt to changing conditions on the water.

The NAVpilot-500 features a comprehensive set of integration options, including compatibility with various types of navigation and communication equipment. This capability allows for effective integration with Furuno's proprietary chart plotters and radar systems, ultimately enhancing situational awareness and safety while navigating.

Moreover, the system offers customizable autopilot modes, including modes for auto and standby operation. This versatility allows users to choose the most suitable steering method for their specific needs, whether for leisurely cruising or during heavy-duty fishing operations. The NAVpilot-500 also incorporates advanced safety features, such as target tracking and collision avoidance, ensuring that operators remain vigilant and prepared for any potential hazards.

Furuno's NAVpilot-500 is engineered for durability and reliability, meeting the rigorous standards set by the maritime industry. Robust construction allows it to withstand harsh marine environments, providing peace of mind to operators. With its blend of advanced technology, user-friendly design, and reliable performance, the NAVpilot-500 stands out as one of the leading autopilot systems in the market today. Whether for leisure or professional use, this system brings a level of sophistication and safety that enhances navigation experiences across various maritime applications.
Top Page Image Contents