Furuno NAVpilot-500 manual Selecting sailing method of NAV mode, NAV mode, Course and XTE

Page 25

3. STEERING MODES

3.3.2Selecting sailing method of NAV mode

The NAV mode has two sailing methods, COURSE and XTE. When the ship goes out from the course between starting point (previous waypoint for route) and destination waypoint because of tide, wind etc, each method functions as below.

COURSE line

Waypoint

Original course

XTE line

NAV mode, COURSE and XTE

A sailing method can be selected from the menu.

1.In the NAV mode, press the [MENU] key to show the NAV mode menu.

2.Rotate the [ENTER] knob to select “NAV MODE”, and then press the [ENTER] knob to show the nav mode options window.

XTE

COURSE

Nav mode options window

3.Rotate the [ENTER] knob to select XTE or COURSE as appropriate.

XTE: The boat sails along the course between the starting point and waypoint.

COURSE: The boat goes directly to the waypoint when the boat is off course.

4.Press the [ENTER] knob, [MENU] key in order to close the menu.

3-6

Image 25
Contents Autopilot Safety Instructions Table of Contents Iii AlarmsForeword FeaturesWord to the Owner of the NAVpilot-500 System configuration of NAVpilot-500 System ConfigurationThis page is intentionally left blank Principle of Autopilot Principle of the AutopilotPrinciple of Operation Operating Controls Basic OperationControl unit, front view Turning On/Off Turning the power offStartup sequence Displays Adjusting Brilliance and ContrastContrast, brilliance window DisplaysSelecting the data shown on Normal and Data Displays Screen setup menuSelecting data for Normal Display 2 screen Normal DisplayDisplayed data Data available for display in Screen 2 Upper and LowerData Displays Selecting the display layout for Data DisplayScreen 3 pattern options window Selecting data for Data DisplayGraphic options window Selecting the display on Graphic DisplayGraphic displays Display setup menu Selecting data for analog indicatorNormal Display 1 Rudder Angle Analog indicator bar options windowThis page is intentionally left blank Stby mode display Stby ModeSteering Modes Using the Auto mode Auto ModeAuto mode display Advanced Auto mode display Advanced Auto modeEnabling the Advanced Auto mode Advanced auto options windowTurn setting window Turn mode For Auto modeTurn Starting the NAV mode NAV ModeNAV mode display Nav mode options window Selecting sailing method of NAV modeNAV mode, Course and XTE Waypoint switching options window Switching waypointNAV mode menu OFF Fishing mode options windowDo not use the Orbit mode in rough sea Orbit modeFishing mode window Navigating to TLL point Fishing modeClover Leaf OrbitDial type remote controller FAP-5551 Remote ModeRotating dial Turning power off dial typeNFU No Follow-Up mode display Turning power on, button and lever type remote controllersTurning power off, button and lever type remote controllers Operating remote controller ex. button and lever typesStby mode menu Selecting course after the Remote mode is offSystem setup menu Cse course after remote options window Course after remote controller is turned offDodging in Stby mode Dodge ModeDodge mode display Dodging in Auto or NAV mode Offsetting data Stby Mode MenuMenu Operation Data calibration menuShip’s speed, temperature, depth calibration Offsetting the heading dataSelecting the selecting method of magnetic variation Magnetic variation options windowParameter setup menu Setting parametersSelecting the method of entering the parameter Sea state options windowDeviation level options window MANUAL-CALMExample of Manual parameter Setting parameters manuallyRudder angle and rudder gain setting Track line and weather setting valueWeather Rudder GainGeneral guidelines for setting counter rudder gain General guidelines for setting rudder gainCounter Rudder Auto trim options window Adjusting the sensitivity in monitoring the boat’s trimAuto net towing options window When towing the netSpeed unit options window, for example Setting the units of measurementsDDMM.MM’ Activating key beep Setting other menu itemsKey beep options window Locking the control unit Setting the panel dimmerLock options window Selecting languageRunning simulation program Simulation mode options windowAlarm Menu AlarmsAlarm menu Audio alarm options window Selecting the alarm buzzerAlarm interval options window Selecting the beep patternSetting the heading deviation alarm Setting the watch alarmSetting the cross-track error limit Watch alarm options windowHow to use XTE alarm Into mode Setting the speed alarmApplication of XTE alarm Speed alarm options windowDepth alarm options window Setting the depth alarmSetting the trip distance alarm Setting the temperature alarmTemp alarm options window Log trip options windowClearing the trip distance Alarm InformationLog trip clear options window Alarm messages, their meanings and priorities Alarm messagesPreventive Maintenance Maintenance & TroubleshootingMaintenance program Check point RemedyDiagnostics Replacement of FuseParts Name Type Code No Remarks Test options windowController Unit Test Processor Unit TestHeading Sensor Test Screen Test Keyboard TestRudder test Rudder Setup and Auto TestSystem Data Clearing MemoriesSystem data screen Memory clear options windowError messages Error MessagesError message Meaning Remedy Error messages con’t MN-1 Menu TreeMN-2 Stby mode menuMN-3 Auto mode menuControl Unit NAVpilot-500Processor Unit InterfaceEnvironmental Conditions Power SupplyColor IN-1 Index
Related manuals
Manual 73 pages 25.32 Kb

NAVpilot-500 specifications

The Furuno NAVpilot-500 is an advanced autopilot system designed for a range of vessels, from small boats to larger commercial ships. This cutting-edge technology provides reliable steering assistance, ensuring enhanced navigational safety and improved operational efficiency. With its versatile functionalities, the NAVpilot-500 has made a significant impact in the maritime industry.

One of the standout features of the Furuno NAVpilot-500 is its use of FURUNO's proprietary technology, including advanced sensors and algorithms. This system leverages a dual-processor architecture, allowing for seamless performance in diverse sea conditions. The NAVpilot-500 is capable of handling course control with impressive precision, adjusting automatically to wind and waves to maintain a steady course.

Another notable aspect of this autopilot system is the intuitive user interface. The large, sunlight-readable display provides easy access to all functionalities and settings, making it user-friendly for operators of varying expertise levels. The touchscreen interface allows for straightforward navigation through menus, ensuring that users can quickly adapt to changing conditions on the water.

The NAVpilot-500 features a comprehensive set of integration options, including compatibility with various types of navigation and communication equipment. This capability allows for effective integration with Furuno's proprietary chart plotters and radar systems, ultimately enhancing situational awareness and safety while navigating.

Moreover, the system offers customizable autopilot modes, including modes for auto and standby operation. This versatility allows users to choose the most suitable steering method for their specific needs, whether for leisurely cruising or during heavy-duty fishing operations. The NAVpilot-500 also incorporates advanced safety features, such as target tracking and collision avoidance, ensuring that operators remain vigilant and prepared for any potential hazards.

Furuno's NAVpilot-500 is engineered for durability and reliability, meeting the rigorous standards set by the maritime industry. Robust construction allows it to withstand harsh marine environments, providing peace of mind to operators. With its blend of advanced technology, user-friendly design, and reliable performance, the NAVpilot-500 stands out as one of the leading autopilot systems in the market today. Whether for leisure or professional use, this system brings a level of sophistication and safety that enhances navigation experiences across various maritime applications.